v1.9.0 -- CLK frequency in RST events:
- RST events (sub_type 0x10) append the measured CLK frequency when known:
[direction, level, flags, clk_hz_be32], flags bit 0 = rate present; the
3-byte form is kept when the rate is not yet measured. Value is
samplerate / _samples_per_clock from the existing 16-edge measurement (PPS
changes F/D, not the CLK rate). VCC events unchanged. Backward
compatible (old consumers read the first two bytes only); consumers can
compute data_rate = clk_hz x D / F from the ATR/PPS Fi/Di.
- Unit tests for the payload codec; README/README_RUS/AGENTS updated.
v1.9.1 -- T=0 NULL is not an SW1:
- The 'scan for SW1' loops accepted any 0x6X byte, including the NULL
procedure byte 0x60 (card busy), so 'NULL + real SW1' was mis-framed as
the status word: the phone traces' SELECT MF came out as ...3f00 6061 —
real SW1 0x61 eaten as SW2, real SW2 0x29 left on the wire and discarded
as a suspicious CLA (desync cascade).
- plausible_sw() now accepts 0x61-0x6F and 0x90-0x9F only, per
ISO 7816-3:2006 10.3.3 Table 11 ('6X' or '9X', EXCEPT '60'; ISO 7816-4
enforces '60' as an invalid SW1) and UICC_SPECS.md 1.8. All seven
SW1-detection sites use plausible_sw(); NULLs met while scanning are
logged as rate-limited wait extensions (_note_pre_sw) instead of
suspicious bytes.
- tools/vs_reader.py::_plausible_sw() mirrors the fix; regression vector
for the 00a40004023f006061 artifact.
Validation: 74/74 unit tests; baseline regenerated and IDENTICAL (the SW
fix is count-neutral -- only the SW bytes change); all 9 example pcaps
regenerated -- vs_reader OK, zero APDUs ending in 60 61, SELECT MF now
61 29 / 61 25.
The recommended tap is the short cable with external pull resistors whose
pins are fixed and known in advance (D5=CLK, D0=I/O, D4=RST, D2=VCC), so
the auto-detection tool is no longer needed. Drop it and all references:
- Delete tools/detect_pins.py.
- README: replace the 'Detecting the wiring' section with a fixed-wiring
note; drop the Python/numpy prerequisite and the detect_pins capture
step from the Windows guide.
- setup.bat: remove the Python/numpy check and the 'find the wiring' next
step.
- pd.py: remove _lock_etu_from_edges (long-disabled) and the no-op
while-True FIND START wrapper.
- pd.py: re-raise SystemError (libsigrokdecode's clean EOF signal) in the
six 'except Exception: pass' guards so put()/wait() at end-of-capture
exits cleanly instead of being swallowed.
- pd.py: fix _measure_clock_period docstring (averages, not robust-min);
drop stale 'line 1633' comment; document the synthetic pcap UDP header
(zero IP checksum / fixed loopback+ports are intentional).
- signal_diagnostic.py: add --max-samples cap + document whole-capture
RAM cost; fix stale '--rst/--vcc=ignore' guidance (-> --no-rst/--no-vcc).
- tests: make test_valid_cla_interindustry_classes use subTest (was a
no-op tuple expression).
- start.sh/start.bat: note the -A multi-spec form is sigrok-cli 0.7.x.
- Remove stale tests/baseline_new.txt (v1.1.3-era, ATR-included mode).
- Add top-level LICENSE (GPL-2.0-or-later).
- pd.py ts_from_samplenum: drop c_uint32 truncation + dead sampleOverflowCount
(pcap timestamps wrapped backwards past ~4.5 min at 16 MHz).
- pd.py handle_atr: guard None reads at EOF (was TypeError (None & 0x80) on a
capture truncated mid-ATR-hunt).
- start.bat: add --protocol (+ :protocol=T=0 default) to match start.sh's
mid-session decode; correct the 'flag-for-flag' header comment.
- start.sh: reject --rst/--vcc assigned to the same pin (was unchecked).
- setup.bat: set DEVICE_MSG on blocked/skipped probe so the trailing
'unknown' message is suppressed.
- vs_reader.py: RESULT now fails on CONCAT / payload mismatch / suspicious
CLA, not just GARBAGE (OK text unchanged; clean traces stay identical).
Residual CONCAT mis-frames (4gmodem/A55_sim2/S21p_sim2) traced to a silent
5-byte drop at an invalid-INS T=0 header (0x0f 00 a4 08 04). Drop only the
stray leading byte and re-frame the remaining four via _replay so the real
command (00 a4 08 04 02 2f 00 -> 61 1c) is recovered.
- _note_discard()/_consume_first(): every consumed-but-unemitted byte is
now logged; idle 0x00/0xFF discards are rate-limited, real data always
gets an ANN_WARN annotation.
- All read-until-SW loops log skipped non-SW bytes.
- All traces: CONCAT 0; BAD_FCS/GARBAGE 0; test_8/test_7 RESULT OK;
47/47 unit tests; baseline byte-identical.
History rewritten to a single root commit so no example trace is stored
in the repo (fixtures are local-only, gitignored). README keeps only
generic <trace>.sr placeholders; AGENTS.md retains the fixture names.
catarrh