catarrh
e1903649a7
- pd.py: remove _lock_etu_from_edges (long-disabled) and the no-op while-True FIND START wrapper. - pd.py: re-raise SystemError (libsigrokdecode's clean EOF signal) in the six 'except Exception: pass' guards so put()/wait() at end-of-capture exits cleanly instead of being swallowed. - pd.py: fix _measure_clock_period docstring (averages, not robust-min); drop stale 'line 1633' comment; document the synthetic pcap UDP header (zero IP checksum / fixed loopback+ports are intentional). - signal_diagnostic.py: add --max-samples cap + document whole-capture RAM cost; fix stale '--rst/--vcc=ignore' guidance (-> --no-rst/--no-vcc). - tests: make test_valid_cla_interindustry_classes use subTest (was a no-op tuple expression). - start.sh/start.bat: note the -A multi-spec form is sigrok-cli 0.7.x. - Remove stale tests/baseline_new.txt (v1.1.3-era, ATR-included mode). - Add top-level LICENSE (GPL-2.0-or-later).
119 lines
5.4 KiB
Batchfile
119 lines
5.4 KiB
Batchfile
@echo off
|
|
rem sigrok_iso7816_stream launcher (Windows): capture ISO 7816 and stream
|
|
rem GSMTAP to :4729. Mirrors the core start.sh flags (channel/samplerate/
|
|
rem clock/gsmtap/pcap/protocol/debug); start.sh has the full flag set.
|
|
|
|
setlocal EnableExtensions EnableDelayedExpansion
|
|
|
|
set "CLK=D5"
|
|
set "DATA=D0"
|
|
set "RST=D4"
|
|
set "VCC=D2"
|
|
set "SAMPLERATE=16M"
|
|
set "CLOCK=native"
|
|
set "HOST=127.0.0.1"
|
|
set "PORT=4729"
|
|
set "PCAP="
|
|
set "DEBUG="
|
|
rem Annotation rows (multi-spec form is sigrok-cli 0.7.x syntax; pin on upgrade)
|
|
set "ANNOT=iso7816=apdus,iso7816=warnings"
|
|
set "PROTOCOL=T=0"
|
|
|
|
:argloop
|
|
if "%~1"=="" goto :argsdone
|
|
if /i "%~1"=="--clk" ( set "CLK=%~2" & shift & shift & goto :argloop )
|
|
if /i "%~1"=="--data" ( set "DATA=%~2" & shift & shift & goto :argloop )
|
|
if /i "%~1"=="--rst" ( set "RST=%~2" & shift & shift & goto :argloop )
|
|
if /i "%~1"=="--vcc" ( set "VCC=%~2" & shift & shift & goto :argloop )
|
|
if /i "%~1"=="--samplerate" ( set "SAMPLERATE=%~2" & shift & shift & goto :argloop )
|
|
if /i "%~1"=="--clock" ( set "CLOCK=%~2" & shift & shift & goto :argloop )
|
|
if /i "%~1"=="--host" ( set "HOST=%~2" & shift & shift & goto :argloop )
|
|
if /i "%~1"=="--port" ( set "PORT=%~2" & shift & shift & goto :argloop )
|
|
if /i "%~1"=="--pcap" ( set "PCAP=%~2" & shift & shift & goto :argloop )
|
|
if /i "%~1"=="--debug" ( set "DEBUG=1" & set "ANNOT=iso7816" & shift & goto :argloop )
|
|
if /i "%~1"=="--protocol" ( set "PROTOCOL=%~2" & shift & shift & goto :argloop )
|
|
if /i "%~1"=="--no-rst" ( set "RST=" & shift & goto :argloop )
|
|
if /i "%~1"=="--no-vcc" ( set "VCC=" & shift & goto :argloop )
|
|
if /i "%~1"=="-h" ( goto :usage )
|
|
if /i "%~1"=="--help" ( goto :usage )
|
|
echo Unknown option: %~1
|
|
exit /b 1
|
|
|
|
:usage
|
|
echo Usage: %~n0 [OPTIONS]
|
|
echo --clk=CH CLK channel default: %CLK%
|
|
echo --data=CH I/O channel default: %DATA%
|
|
echo --rst=CH RST channel default: %RST%
|
|
echo --vcc=CH VCC channel default: %VCC%
|
|
echo --samplerate=SR Sample rate default: %SAMPLERATE%
|
|
echo --clock=MODE native/detect/sample_as_clock
|
|
echo --host=IP GSMTAP destination default: 127.0.0.1
|
|
echo --port=N GSMTAP port default: 4729
|
|
echo --pcap=FILE Also write decoded events to FILE (no spaces in path)
|
|
echo --debug Full decoder + sigrok output (all annotation rows + -l 4).
|
|
echo
|
|
echo By default only decoded APDUs and decoder warnings/errors are shown.
|
|
echo --protocol=MODE T=0 (default), T=1, or auto (mid-session decode)
|
|
echo --no-rst Disable RST tracking
|
|
echo --no-vcc Disable VCC tracking
|
|
echo.
|
|
echo To log output on Windows use redirection: %~n0 ... ^> capture.log 2^>^&1
|
|
exit /b 0
|
|
|
|
:argsdone
|
|
set "SIGROK_EXE="
|
|
rem Try known install locations (order: 64-bit, 32-bit, then PATH)
|
|
if not defined SIGROK_EXE if exist "%ProgramFiles%\sigrok\sigrok-cli\sigrok-cli.exe" set "SIGROK_EXE=%ProgramFiles%\sigrok\sigrok-cli\sigrok-cli.exe"
|
|
if not defined SIGROK_EXE if exist "%ProgramFiles(x86)%\sigrok\sigrok-cli\sigrok-cli.exe" set "SIGROK_EXE=%ProgramFiles(x86)%\sigrok\sigrok-cli\sigrok-cli.exe"
|
|
if not defined SIGROK_EXE if exist "%ProgramFiles%\sigrok\PulseView\sigrok-cli.exe" set "SIGROK_EXE=%ProgramFiles%\sigrok\PulseView\sigrok-cli.exe"
|
|
if not defined SIGROK_EXE if exist "%ProgramFiles(x86)%\sigrok\PulseView\sigrok-cli.exe" set "SIGROK_EXE=%ProgramFiles(x86)%\sigrok\PulseView\sigrok-cli.exe"
|
|
if not defined SIGROK_EXE where sigrok-cli >nul 2>&1 && for /f "delims=" %%i in ('where sigrok-cli') do set "SIGROK_EXE=%%i"
|
|
if not defined SIGROK_EXE goto :notfound
|
|
for %%i in ("!SIGROK_EXE!") do set "SIGROK_DIR=%%~dpi"
|
|
if "!SIGROK_DIR:~-1!"=="\" set "SIGROK_DIR=!SIGROK_DIR:~0,-1!"
|
|
set "PATH=!SIGROK_DIR!;!PATH!"
|
|
goto :found
|
|
|
|
:notfound
|
|
echo [X] sigrok-cli not found.
|
|
echo Searched:
|
|
echo %ProgramFiles%\sigrok\sigrok-cli
|
|
echo %ProgramFiles(x86)%\sigrok\sigrok-cli
|
|
echo %ProgramFiles%\sigrok\PulseView
|
|
echo %ProgramFiles(x86)%\sigrok\PulseView
|
|
echo PATH
|
|
echo Install from https://sigrok.org/wiki/Downloads
|
|
exit /b 1
|
|
|
|
:found
|
|
|
|
rem Normalize --protocol to the decoder's accepted form (T=0 / T=1 / auto).
|
|
if /i "%PROTOCOL%"=="T0" set "PROTOCOL=T=0"
|
|
if /i "%PROTOCOL%"=="T1" set "PROTOCOL=T=1"
|
|
if /i "%PROTOCOL%"=="AUTO" set "PROTOCOL=auto"
|
|
|
|
set "OPTS=clk=%CLK%:data=%DATA%:clock_option=%CLOCK%"
|
|
set "OPTS=%OPTS%:gsmtap_host=%HOST%:gsmtap_port=%PORT%"
|
|
if defined RST set "OPTS=%OPTS%:rst=%RST%:rst_detect=true"
|
|
if defined VCC set "OPTS=%OPTS%:vcc=%VCC%:vcc_detect=true"
|
|
if defined PCAP set "OPTS=%OPTS%:pcap_file=%PCAP%"
|
|
set "OPTS=%OPTS%:protocol=%PROTOCOL%"
|
|
|
|
set "CMDLINE=sigrok-cli -d fx2lafw --config samplerate=%SAMPLERATE% --continuous -C D0,D1,D2,D3,D4,D5,D6,D7"
|
|
if defined DEBUG set "CMDLINE=%CMDLINE% -l 4"
|
|
set "CMDLINE=%CMDLINE% -P iso7816:%OPTS% -A %ANNOT%"
|
|
|
|
echo ISO 7816 streamer - clk=%CLK% data=%DATA% clock=%CLOCK%
|
|
if defined RST echo RST tracking on channel %RST%
|
|
if defined VCC echo VCC tracking on channel %VCC%
|
|
if defined PCAP echo PCAP output: %PCAP%
|
|
echo Samplerate: %SAMPLERATE% ^| GSMTAP -^> %HOST%:%PORT%
|
|
echo Capture runs until you press Ctrl+C.
|
|
echo.
|
|
|
|
rem <NUL detaches stdin (best-effort to disable sigrok's "press any key
|
|
rem to stop acquisition" prompt); not verified on Windows, where the
|
|
rem prompt may read the console rather than stdin.
|
|
%CMDLINE% <NUL
|
|
exit /b %errorlevel%
|