35 Commits

Author	SHA1	Message	Date
Kévin Redon	7fc392aabf	schematic: make it more readable ... - VCC is up - GND is down - group the parts by functionality and use net name - separate decoupling capacitors - arrange groups from left input to right output Change-Id: I2d894dd10b8b619ccbce1ae8b7e25316963157c8	2019-09-03 14:48:23 +02:00
King Kévin	6279da6fe0	change microcontroller to SAM3S	2015-07-05 09:58:19 +02:00
Harald Welte	3fc0e7da79	Update BOM for v1.4 ... * AT91SAM128D, not C, as old is EOL * New ferrite bead / filter, as old is EOL. * Flash S25FL032P0XMFI011, was already populated in v1.3	2014-06-26 11:34:44 +02:00
Kevin Redon	2a63d76a74	export schematic, and pcb (with minor esthetic corrections)	2014-06-23 00:23:40 -07:00
Harald Welte	21f7718e2f	v1.4: Connect PA0 to 3V3; pull-up for PA1/PA2 (R25,R26) ... PA0, PA1 and PA2 must be high during reset to enter SAM-BA mode.	2014-06-20 15:39:02 +02:00
Harald Welte	2aed3f177b	simtrace 1.3: move point of origin to lower left corner of PCB	2013-11-11 15:30:59 +01:00
Kevin Redon	e9e54e8d80	merge	2013-10-28 11:15:44 +01:00
Kevin Redon	976b0a0a9f	BOM corrected (sorted by value) and reformated	2013-10-28 11:00:33 +01:00
Harald Welte	c5b69fb194	re-add BOM spreadsheet with updated v1.3 components	2013-10-27 18:54:45 +01:00
Kevin Redon	ab6f2d1a19	MCU pin 48 used to identify v1.3 by putting it to ground (with internal pull-up)	2013-10-27 17:11:29 +01:00
Kevin Redon	b8671cab1f	exported fabrication files	2013-10-27 12:49:58 +01:00
Harald Welte	4f0bebb1f9	Mark IC5 as "do not place" (VCC_Forward) as it doesn't work anyway ... If the LDO is switched off, then even if we try to forward power from the phone to the SIM, the current will sink inside the LDO (no reverse current protection).	2012-05-19 22:02:35 +02:00
Kevin Redon	6dcf692dfa	RST_PHONE pulldown added on PCB	2012-05-18 19:30:06 +02:00
Kevin Redon	1c82a64101	v1.2p fabrication exported	2012-05-16 19:52:14 +02:00
Kevin Redon	2b9d0c26a1	hw: fabrication output generated	2011-12-06 00:39:30 +01:00
Kevin Redon	88a018b3e2	hw: sysmocom added to copper, gerber rendered	2011-11-05 21:30:26 +01:00
Kevin Redon	e2ae9ddbde	hw: solder mask between at91sam7s added	2011-11-05 19:06:28 +01:00
Kevin Redon	3fc51e7fc5	v1.0p corrected and rendered. BOM updated	2011-07-02 21:01:21 +02:00
Kevin Redon	ba3363e1c0	D2 and D3 now also use STPS340U instead of 1N5819	2011-07-02 19:59:11 +02:00
Kevin Redon	f54394ed28	BOM updated for production	2011-07-02 13:41:47 +02:00
Kevin Redon	34eaeb1684	PS/gerber rendered for production	2011-07-02 13:37:01 +02:00
Kevin Redon	b35578b117	BOM updated	2011-06-23 13:22:37 +02:00
Kevin Redon	199cc31535	PCB PS drawings were in the wrong folder	2011-06-23 12:15:36 +02:00
Kevin Redon	ff03d7e879	ps/gerber rerendered for the thermal footprints	2011-06-23 00:20:49 +02:00
Kevin Redon	5359f93f07	v1.0 released. board version added, output (schema,gerber) rendered	2011-06-21 15:48:25 +02:00
Kevin Redon	96bba80232	wrong USB connector from digikey in BOM chosen. corrected : hirose UX60-MB-5ST / digikey H2959CT-ND	2011-06-21 14:58:49 +02:00
Kevin Redon	35c53726c9	output rendered	2011-06-21 02:44:26 +02:00
Kevin Redon	cc08944c5c	BOM updated, partially	2011-06-20 23:38:59 +02:00
Kevin Redon	bcd3695c1a	LDO, and power switch added. not verified yet	2011-06-20 22:50:22 +02:00
Kevin Redon	13b6eff33a	bus switch CB3q3244 used instead of QS3244	2011-06-20 17:26:04 +02:00
Kevin Redon	44acd46f35	USB changed, BOM updated	2011-06-20 13:14:30 +02:00
Kevin Redon	0ffd081460	USB_PUP all whole board rerouted	2011-06-15 16:12:13 +02:00
Kevin Redon	3914ee6b2b	debug port changed	2011-05-22 15:54:51 +02:00
Kevin Redon	6684648591	board rerouted	2011-05-17 13:25:49 +02:00
Kevin Redon	7c7336c677	pcb drawings & gerber added	2011-05-15 19:40:50 +02:00