diff --git a/sam3s_example/include/board.h b/sam3s_example/include/board.h index 5554d6ed..140e8e92 100644 --- a/sam3s_example/include/board.h +++ b/sam3s_example/include/board.h @@ -67,16 +67,28 @@ /// Smartcard detection pin -// FIXME: add connect pin as iso pin -#define SMARTCARD_CONNECT_PIN {1 << 8, PIOA, ID_PIOA, PIO_INPUT, PIO_DEFAULT} +// FIXME: add connect pin as iso pin...should it be periph b or interrupt oder input? +#define BOARD_ISO7816_BASE_USART USART0 +#define BOARD_ISO7816_ID_USART ID_USART0 + +#define SIM_PWEN_PIN {PIO_PA5, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT} + +#define SW_SIM PIO_PA8 +#define SMARTCARD_CONNECT_PIN {SW_SIM, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_IT_EDGE } +//#define SMARTCARD_CONNECT_PIN {SW_SIM, PIOB, ID_PIOB, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_IT_EDGE} /// PIN used for reset the smartcard -#define PIN_SIM_IO {PIO_PA1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} -#define PIN_SIM_CLK {PIO_PA2, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} +//#define RST_SIM (1 << 7) +#define RST_SIM (1 << 7) +// FIXME: Card is resetted with pin set to 0 --> PIO_OUTPUT_1 as default is right? +#define PIN_ISO7816_RSTMC {RST_SIM, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_PULLUP} -#define PIN_ISO7816_RSTMC {1 << 7, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT} /// Pins used for connect the smartcard +#define PIN_SIM_IO {PIO_PA1, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} +#define PIN_SIM_IO2 {PIO_PA6, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} +#define PIN_SIM_CLK {PIO_PA2, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} +#define PIN_SIM_CLK2 {PIO_PA4, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT} //#define PINS_ISO7816 PIN_USART1_TXD, PIN_USART1_SCK, PIN_ISO7816_RSTMC -#define PINS_ISO7816 PIN_SIM_IO, PIN_SIM_CLK, PIN_ISO7816_RSTMC +#define PINS_ISO7816 PIN_SIM_IO, PIN_SIM_IO2, PIN_SIM_CLK, PIN_SIM_CLK2, PIN_ISO7816_RSTMC, SIM_PWEN_PIN #endif diff --git a/sam3s_example/mains/iso7816.c b/sam3s_example/mains/iso7816.c new file mode 100644 index 00000000..05b2b3da --- /dev/null +++ b/sam3s_example/mains/iso7816.c @@ -0,0 +1,381 @@ +/* ---------------------------------------------------------------------------- + * ATMEL Microcontroller Software Support + * ---------------------------------------------------------------------------- + * Copyright (c) 2009, Atmel Corporation + * + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * - Redistributions of source code must retain the above copyright notice, + * this list of conditions and the disclaimer below. + * + * Atmel's name may not be used to endorse or promote products derived from + * this software without specific prior written permission. + * + * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR + * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE + * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, + * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF + * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING + * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, + * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * ---------------------------------------------------------------------------- + */ + +/** + * \page usart_iso7816 USART ISO7816 Example + * + * \section Purpose + * This example sends ISO 7816 commands to a smartcard connected to the + * evaluation kits on sam3s. + * + * \section Requirements + * This example can be used on sam3s evaluation kit. Please connect the + * smartcard contacts with following pins which could be easily wired from + * the board. + * - SAM3S-EK -- SMARTCARD + * - PA11 -- RST + * - TXD1(PA22) -- I/O + * - SCK1(PA23) -- CLK + * + * \section Description + * The iso7816 software provide in this examples is use to transform APDU + * commands to TPDU commands for the smart card. + * The iso7816 provide here is for the protocol T=0 only. + * The send and the receive of a character is made under polling. + * In the file ISO7816_Init is defined all pins of the card. User must have to + * change this pins according to his environment. + * The driver is compliant with CASE 1, 2, 3 of the ISO7816-4 specification. + * + * \section Usage + * -# Build the program and download it inside the evaluation board. Please + * refer to the SAM-BA User Guide, + * the GNU-Based Software Development + * application note or to the IAR EWARM User Guide, + * depending on your chosen solution. + * -# On the computer, open and configure a terminal application (e.g. + * HyperTerminal on Microsoft Windows) with these settings: + * - 115200 bauds + * - 8 data bits + * - No parity + * - 1 stop bit + * - No flow control + * -# Connect the card reader to sam3s-ek board: + * + * + * + * + *
C1: Vcc: 7816_3V5V C5: Gnd C4: RFU
C2: Reset: 7816_RST C6: Vpp C8: RFU
C3: Clock: 7816_CLK C7: 7816_IO
+ * If necessary,another pin must be connected on the card reader for detecting the + * insertion and removal: 7816_IRQ. + * On Atmel boards, all this pins can be easily connecting with jumpers. + * -# Start the application. The following traces shall appear on the terminal: + * \code + * -- USART ISO7816 Example xxx -- + * -- xxxxxx-xx + * -- Compiled: xxx xx xxxx xx:xx:xx -- + * Display the ATR + * \endcode + * + * \section References + * - usart_iso7816/main.c + * - iso7816_4.c + * - pio.h + * - usart.h + * + */ + +/** \file + * + * This file contains all the specific code for the usart_iso7816 example. + * + */ + + +/*------------------------------------------------------------------------------ + * Headers + *------------------------------------------------------------------------------*/ + +#include "board.h" + +#include + +/*------------------------------------------------------------------------------ + * Internal definitions + *------------------------------------------------------------------------------*/ + +/** Maximum ucSize in bytes of the smartcard answer to a command.*/ +#define MAX_ANSWER_SIZE 10 + +/** Maximum ATR ucSize in bytes.*/ +#define MAX_ATR_SIZE 55 + +/*------------------------------------------------------------------------------ + * Internal variables + *------------------------------------------------------------------------------*/ + +/** Test command #1.*/ +static const uint8_t testCommand1[] = {0x00, 0x10, 0x00, 0x00}; +/** Test command #2.*/ +static const uint8_t testCommand2[] = {0x00, 0x20, 0x00, 0x00, 0x02}; +/** Test command #3.*/ +static const uint8_t testCommand3[] = {0x00, 0x30, 0x00, 0x00, 0x02, 0x0A, 0x0B}; +/* Select MF */ +static const uint8_t testCommand4[] = {0x00, 0xa4, 0x00, 0x00, 0x02, 0x3f, 0x00}; +/** ISO7816 pins */ +static const Pin pinsISO7816[] = {PINS_ISO7816}; +/** ISO7816 RST pin */ +static const Pin pinIso7816RstMC = PIN_ISO7816_RSTMC; +static uint8_t sim_inserted = 0; +/*------------------------------------------------------------------------------ + * Internal functions + *------------------------------------------------------------------------------*/ + +/*------------------------------------------------------------------------------ + * Optional smartcard detection + *------------------------------------------------------------------------------*/ + +#ifdef SMARTCARD_CONNECT_PIN + +/** Smartcard detection pin.*/ +static const Pin pinSmartCard = SMARTCARD_CONNECT_PIN; + +/** + * PIO interrupt service routine. Checks if the smartcard has been connected + * or disconnected. + */ +static void ISR_PioSmartCard( const Pin *pPin ) +{ +/* FIXME: why is pinSmartCard.pio->PIO_ISR the wrong number? + printf("+++++ Trying to check for pending interrupts (PIO ISR: 0x%X)\n\r", pinSmartCard.pio->PIO_ISR); + printf("+++++ Mask: 0x%X\n\r", pinSmartCard.mask); +Output: + +++++ Trying to check for pending interrupts (PIO ISR: 0x400)) = 1<<10 + +++++ Mask: 0x100 = 1<<8 +*/ + /* Check all pending interrupts */ + if ( (pinSmartCard.pio->PIO_ISR & pinSmartCard.mask) != 0 ) + { + /* Check current level on pin */ + if ( PIO_Get( &pinSmartCard ) == 0 ) + { + sim_inserted = 1; + printf( "-I- Smartcard inserted\n\r" ) ; + } + else + { + sim_inserted = 0; + printf( "-I- Smartcard removed\n\r" ) ; + } + } +} + +/** + * Configures the smartcard detection pin to trigger an interrupt. + */ +static void ConfigureCardDetection( void ) +{ + printf("+++++ Configure PIOs\n\r"); + PIO_Configure( &pinSmartCard, 1 ) ; + NVIC_EnableIRQ( PIOA_IRQn ); +// FIXME: Do we need to set priority?: NVIC_SetPriority( PIOA_IRQn, 10); + PIO_ConfigureIt( &pinSmartCard, ISR_PioSmartCard ) ; + PIO_EnableIt( &pinSmartCard ) ; +} + +#else + +/** + * Dummy implementation. + */ +static void ConfigureCardDetection( void ) +{ + printf( "-I- Smartcard detection not supported.\n\r" ) ; +} + +#endif + +/** + * Displays a menu which enables the user to send several commands to the + * smartcard and check its answers. + */ +static void SendReceiveCommands( void ) +{ + uint8_t pMessage[MAX_ANSWER_SIZE]; + uint8_t ucSize ; + uint8_t ucKey ; + uint8_t command; + uint8_t i; + + /* Clear message buffer */ + memset( pMessage, 0, sizeof( pMessage ) ) ; + + /* Display menu */ + printf( "-I- The following three commands can be sent:\n\r" ) ; + printf( " 1. " ) ; + for ( i=0 ; i < sizeof( testCommand1 ) ; i++ ) + { + printf( "0x%X ", testCommand1[i] ) ; + } + printf( "\n\r 2. " ) ; + + for ( i=0 ; i < sizeof( testCommand2 ) ; i++ ) + { + printf( "0x%X ", testCommand2[i] ) ; + } + printf( "\n\r 3. " ) ; + + for ( i=0 ; i < sizeof( testCommand3 ) ; i++ ) + { + printf( "0x%X ", testCommand3[i] ) ; + } + printf( "\n\r 4. " ) ; + + for ( i=0 ; i < sizeof( testCommand4 ) ; i++ ) + { + printf( "0x%X ", testCommand4[i] ) ; + } + printf( "\n\r" ) ; + + /* Get user input */ + ucKey = 0 ; + while ( ucKey != 'q' ) + { + printf( "\r " ) ; + printf( "\rChoice ? (q to quit): " ) ; +#if defined ( __GNUC__ ) + fflush(stdout); +#endif + ucKey = UART_GetChar() ; + printf( "%c", ucKey ) ; + command = ucKey - '0'; + + /* Check user input */ + ucSize = 0 ; + if ( command == 1 ) + { + printf( "\n\r-I- Sending command " ) ; + for ( i=0 ; i < sizeof( testCommand1 ) ; i++ ) + { + printf( "0x%02X ", testCommand1[i] ) ; + } + printf( "...\n\r" ) ; + ucSize = ISO7816_XfrBlockTPDU_T0( testCommand1, pMessage, sizeof( testCommand1 ) ) ; + } + else + { + if ( command == 2 ) + { + printf( "\n\r-I- Sending command " ) ; + for ( i=0 ; i < sizeof( testCommand2 ) ; i++ ) + { + printf("0x%02X ", testCommand2[i] ) ; + } + printf( "...\n\r" ) ; + ucSize = ISO7816_XfrBlockTPDU_T0( testCommand2, pMessage, sizeof( testCommand2 ) ) ; + } + else + { + if ( command == 3 ) + { + printf( "\n\r-I- Sending command " ) ; + for ( i=0 ; i < sizeof( testCommand3 ) ; i++ ) + { + printf( "0x%02X ", testCommand3[i] ) ; + } + printf( "...\n\r" ) ; + ucSize = ISO7816_XfrBlockTPDU_T0( testCommand3, pMessage, sizeof( testCommand3 ) ) ; + } + else + { + if ( command == 4 ) + { + printf( "\n\r-I- Sending command " ) ; + for ( i=0 ; i < sizeof( testCommand4 ) ; i++ ) + { + printf( "0x%02X ", testCommand4[i] ) ; + } + printf( "...\n\r" ) ; + ucSize = ISO7816_XfrBlockTPDU_T0( testCommand4, pMessage, sizeof( testCommand4 ) ) ; + } + } + } + } + + /* Output smartcard answer */ + if ( ucSize > 0 ) + { + printf( "\n\rAnswer: " ) ; + for ( i=0 ; i < ucSize ; i++ ) + { + printf( "0x%02X ", pMessage[i] ) ; + } + printf( "\n\r" ) ; + } + } + + printf( "Quitting ...\n\r" ) ; +} + +/*------------------------------------------------------------------------------ + * Exported functions + *------------------------------------------------------------------------------*/ + +/** + * Initializes the DBGU and ISO7816 driver, and starts some tests. + * \return Unused (ANSI-C compatibility) + */ +extern int main( void ) +{ + uint8_t pAtr[MAX_ATR_SIZE] ; + uint8_t ucSize ; + + LED_Configure(LED_NUM_GREEN); + LED_Set(LED_NUM_GREEN); + + /* Disable watchdog*/ + WDT_Disable( WDT ) ; + + /* Initialize Atr buffer */ + memset( pAtr, 0, sizeof( pAtr ) ) ; + + printf( "-- USART ISO7816 Example %s --\n\r", SOFTPACK_VERSION ) ; + printf( "-- %s\n\r", BOARD_NAME ) ; + printf( "-- Compiled: %s %s --\n\r", __DATE__, __TIME__ ) ; + + /* Configure IT on Smart Card */ + ConfigureCardDetection() ; + + /* Configure ISO7816 driver */ + PIO_Configure( pinsISO7816, PIO_LISTSIZE( pinsISO7816 ) ) ; + +// FIXME: RST seems to be allways low here + printf("******* Reset State1 (1 if the Pin RstMC is high): 0x%X\n\r", ISO7816_StatusReset()); + + ISO7816_Init( pinIso7816RstMC ) ; + + printf("******* Reset State2 (1 if the Pin RstMC is high): 0x%X\n\r", ISO7816_StatusReset()); + + /* Read ATR */ + ISO7816_warm_reset() ; + + ISO7816_Datablock_ATR( pAtr, &ucSize ) ; + printf("******* Reset State3 (1 if the Pin RstMC is high): 0x%X\n\r", ISO7816_StatusReset()); + + /* Decode ATR */ + ISO7816_Decode_ATR( pAtr ) ; + +// FIXME: RST seems to be allways high + printf("******* Reset State4 (1 if the Pin RstMC is high): 0x%X\n\r", ISO7816_StatusReset()); + + /* Allow user to send some commands */ + SendReceiveCommands() ; + + return 0 ; +} +