- improves trace diagnostic output by moving cursor back over the
the rotor before a diagnostic message has a chance to be printed.
there is still a race condition, but it is much better.
Change-Id: Iad7767f2a5dbbd67b0f33b9bfc2c3864ce308990
This fixes the firmware USB interface somehow getting stuck
after a USB disconnect/reconnect without power cycle.
Right now there are a number of things we only execute the first time we
reach USBD_STATE_CONFIGURED, but not at any subsequent such event.
It's also rather clear that this doesn't really show in simtrace2 as it
is bus-powered. And it doesn't show on OWHW as we don't have any USB
unplug situations of the USB between the on-board traces of USB host and
SAM3S. So this really only is relevant to QMOD.
A cheap and dirty work-around is to simply reset the entire uC every
time a USB unplug happens.
Change-Id: I6678bb2192c1419ed388b46c4ae7aa1ce18dc7ee
Related: OS#5578
the ISO7816 UARTs have highest priority, while console has lowest.
remaining sources (USB, ADC, GPIO) are in between.
Change-Id: Ie6c97d61d8da3990b6e44144f36cb6d37d194307
Remove the paragraph about writing to the Free Software Foundation's
mailing address. The FSF has changed addresses in the past, and may do
so again. In 2021 this is not useful, let's rather have a bit less
boilerplate at the start of source files.
Change-Id: Ie0a3b2273383adbb3303faffd6ff96be7f4cae99
This adds support for the new ngff_cardem board, a board that
basically combines a ngff breakout board with a built-in SIMtrace2.
Cardem works, but depending on the modem it might need a adjusted ATR to
ensure a lower baud rate is used by the modem, high rates might lead
to weird power cycling of the card after a few transfers.
Trace was also tested and appears to work as expected.
Change-Id: Ia96124fbe8a752c98e7fd4096d542a3b2b9bc255
Instead of using the timer/counter peripheral to handle the waiting time
and corresponding timeout, the USART peripheral internal timeout
mechanism is used.
This is particularly important for the SIMtrace board since there
(contrary to other boards) the I/O signal is not wired to a TIO pin
of the timer/counter block, and hence Rx/Tx data cannot reset that
timer/counter.
As a result of this migration, cardem is now supported not only on
owhw + qmod, but also on the simtrace board.
The guts of this change have been lifted out of Change-Id
Ibcb2c8cace9137695adf5fb3de43566f7cfb93b5 by Kevin Redon, which was
unfortunately touching various different topics at the same time and
hence was split up. Some improvements are the introduction of the
ENABLE_TX_TIMER_ONLY mode, which avoids the USART interrupt handler
getting hammered with TXRDY between release of RST and start of the ATR.
Change-Id: Ibcb2c8cace9137695adf5fb3de43566f7cfb93b5
Related: OS#1704
This reverts commit 4a58c08d67.
The code replicates to a large extent what is already present in iso7816_fidi.c
and I have serious doubts about the correctness of the computation in
its iso7816_3_calculate_wt() function.
Change-Id: I3f26da4e9aa8d7b0f4b4b7992269cf365a643ec7
In the end we want to share most of this, irrespective of the "APP".
Let's avoid unnecessary differences.
Change-Id: Icf063d4ca79edf66ffbe8e87a915deb77dec478a
This unifies the printing of the welcome banner, and it also ensures
that all modes print all information (serial number, reset cause).
Furthermore the APP and BOARD #defines from the make environment are
also printed.
Change-Id: I7e6bc05cee4b9ec0fd9a05dc90ce0b26a5763e5a
"SIMtrace 2 compatible device" is pretty generic. Let's have the
actual board name inside the string descriptors, giving a more
user friendly experience in case users are issuing 'lsusb' and the
like.
Change-Id: Ibcc338b504bd2a1605e31d7f5eadb7161f547c6a
This string dates back to some very early naming; let's reflect how
we have been calling this in reality for quite some time now.
Change-Id: I5a7497188385706a1e924784073c619fa9bfdd60
There have been tons of format-string related bugs in our code which
we never discovered due to disabling -Wformat. Let's fix that.
Change-Id: I5ec466361bcc526fac1f4897673264ee5af3458b
a lot of the procedures are done in ISRs, but the watchdog is only
reset in the main loop.
this causes frequent reset, particularly at the beginning were
states have to the initialized.
Change-Id: Iad364444fca9d18f9a8cf47d5e0840ccd7bac2ef
This is required to make python pexpect.fdexpect happy, as it
requires that all characters are echo-ed back in order to detect
when the output of a given command starts.
Change-Id: I73b24e43f6c8b86a2766aba67d8307c184448aa0
the curent local copies of libosmocore headers + source is a temporary
hack anyway. We should instead rely on a system-wide install of
libosmocore cross-compiled for arm-none-eabi. But leave that as a
second (later) step beyond this patch.
Change-Id: Ia63fd842d45a2b404233b4326050e7eda0604cf0
We now generalize the USB communiction and abandon the 'req_ctx'
structure inherited from openpcd. Instead we use the libosmocore 'msgb'
structure to handle incoming and outgoing USB tranfers. We also use
linuxlist-based msgb-queues for each endpoint.
This makes sure that we'll re-enumerate on the USB, as a CPU reset
apparently doesn't automatically release the pull-up and notify the hub
that we were gone?
For some strange reason my output is garbled in both the 'screen' and
'cu' teerminal programs and 'raw' terminal (stty) mode. I fail to
understand why, but let's simply adjust the code as needed for now.
