when the host software does not retrieve the USB messages the memory
is filled and no new USB messages can be allocated, preventing the
following code to print the message
Change-Id: Ie8946894a84cb853b45555f7abb1ca6f32111425
TRACE_INFO will also provide the DFU start reason, but TRACE_INFO
(TRACE_LEVEL >= 4) should only be used for debugging.
WARNING: With TRACE_LEVEL >= 4 the DFU binary is over the maximum of
16 kiB allocated for the DFU bootloader.
Thus make combined will not boot the main application because its
start if after the expecte 16 kiB address; and flashing using DFU
will overwrite the DFU bootloader itself.
Change-Id: I82323e0f76c03f67df7dc8f2b6783166cc25f3aa
The qmod does not have a separate force button as simtrace has.
Instead it check is TX and RX of UART are shorted using PIO.
If the pins are not set back to the UART peripheral, the TRACE/debug
console output will not work anymore.
Change-Id: Id434b49909d6395a2f93a00f39d2d770a5725466
The DFU uses the UART peripheral (with IRQ/ISR) for the debug output
console. Before starting the main application we should make sure
this configuration is reset to avoid interference (particularly the
IRQ/ISR).
This is not too important though since the main application
reconfigures the UART for console output.
Other peripheral could also be disabled (e.g. all other PIO used
by DFU), but most of them also get configured by the main application.
Change-Id: I8234d1b85938ad6393094c08183f613ad09ee01b
The stack size is fixed. The linker script puts the stack section
after the bss section. The initial stack pointer is not at the
end of the RAM (as often seen).
Thus the initial stack pointer address of the main application
is different than the one from DFU. When starting the main
application the stack pointer needs to be set to the new value.
If this is not done the main application stack may overwrite the
data in bss, even without exceeding the fixed stack size.
Change-Id: Ie354d603fe302d3d5bdfa9c31575411de722323b
In the SIMtrace and QMOD schematics the LEDs are connected to +3.3V.
Thus to switch the LED on we need to set the pin low.
Change-Id: Id8cc27e6f0b6556ba5e7ea4d254dd0fe59042a0c
the waiting time (WT) is used to detect timeouts (e.g. for
unresponsive card or just to signal an error/NAK). it is essential
to detect to timeout to end current data transfer (e.g. change state).
by default (after a reset) to timeout is 9600 ETU, but this can change
at two places:
- after the ATR using the value of TC2 (if present)
- after a PPS (only F is used, and not D)
because the timeout value can be larger than the 16-bit of the USART
TO register, an external variable needs to be used for the count down.
Change-Id: I9735660ffce161cec8d4e63fa60a66fc8ef57525
Handling the USB message queue is done in an ISR and take quite some time.
This can cause a USART/SIM sniffing buffer overrun, resulting in data loss.
By setting the USB IRQ lower than the USART IRQ, the USB ISR can be
interrupted (for short) and no data gets lost.
Change-Id: I870a0aa8e251bbb53249c54bfcaa45de5b5a9486
don't wait for space to be available in the buffer since since would
prevent from processing non-console (e.g. debug) more important data
Change-Id: Ia625b09eb30bb7b43edd3989f697d8ef33200f28
Use USART 0 connected to the SIM card side to sniff the communication.
The card side can also measure ETU times.
Do proper pin initialization.
This code can already capture the ATR communication between phone and card.
Change-Id: I0597ec723cb2225540c89c3821b91d8a45adfcd6
because the applications share the board capabilities defined in
libboard/*/include/board.h and USB configurations are enabled according
to the previously defined capabilities in libcommon/source.usb.c, all
applications actually offer the same functions.
thus creating the trace application is only mainly a cosmetic change, as the
sniffer function will also be present and enabled in the cardem application.
Change-Id: I24b3500a0905cbd622507722280b3c7e7f188bde
In commit eac1bec428 we start to use the
ringbuffer inside the console printing code. As a result, we must not
use TRACE_*() or printf() from within ringbuffer.c code to avoid
infinite recursion.
Instead, let rbuf_write() return a negative return value in case the
ring buffer overflows. This way, the callers (outside the
console/stdout code) can print an error message themselves.
Change-Id: Ib009f013be119dbad22fa2b7d60ec8dee59baee5
