The default ISR (particularly the HardFault handler) print information,
but this information was not displayed on the console because the UART
IRQ is lower than some default blocking IRQ.
Allowing to set synchronous transfer corrects this.
The underlying Atmel exception library had to be modified to use the
synchronous output.
Making UART_PutChar always synchronous when called from an ISR is not
desired because we use TRACE_ macros is some ISR. The synchronous
output must be set explicitly.
Change-Id: I1b4ace5185cf2dc32684934ed12bf6a8682e9bad
The previous mechanism of retrying a failed write could become a
infinite blocking loop (until watchdog tiemout).
Also the array size is used to know how much data to write and verify
instead of a constant.
Change-Id: I8d2d090c5f4d1195f4c7eb29b3958a7bb05f56ec
The Atmel AT24C02 defines a maximum tWR waiting time after a byte
write of 5 ms before a next write.
Enforcing this wait time also fixed the failed verification in qmod,
where it was reading 0xffff instead of the written value.
Change-Id: I42c90b8d0329e425f275067e87d584212a43a90b
when building the trace app for the simtrace board gcc was outputing
the following error:
libboard/common/source/boardver_adc.c:20:17: warning: 'adc2uv' defined but not used [-Wunused-function]
static uint32_t adc2uv(uint16_t adc)
adc2uv is used by qmod, and defined in two places:
in boardver_adc.c and mode_cardemu.c.
this change will have adc2uv only defined in boardver_adc.c and make
available in the header to be used by mode_cardemu.c.
Change-Id: I8a772638fa8dd02d8bc8b7631de5af5a22647c55
TRACE_INFO will also provide the DFU start reason, but TRACE_INFO
(TRACE_LEVEL >= 4) should only be used for debugging.
WARNING: With TRACE_LEVEL >= 4 the DFU binary is over the maximum of
16 kiB allocated for the DFU bootloader.
Thus make combined will not boot the main application because its
start if after the expecte 16 kiB address; and flashing using DFU
will overwrite the DFU bootloader itself.
Change-Id: I82323e0f76c03f67df7dc8f2b6783166cc25f3aa
The qmod does not have a separate force button as simtrace has.
Instead it check is TX and RX of UART are shorted using PIO.
If the pins are not set back to the UART peripheral, the TRACE/debug
console output will not work anymore.
Change-Id: Id434b49909d6395a2f93a00f39d2d770a5725466
The DFU uses the UART peripheral (with IRQ/ISR) for the debug output
console. Before starting the main application we should make sure
this configuration is reset to avoid interference (particularly the
IRQ/ISR).
This is not too important though since the main application
reconfigures the UART for console output.
Other peripheral could also be disabled (e.g. all other PIO used
by DFU), but most of them also get configured by the main application.
Change-Id: I8234d1b85938ad6393094c08183f613ad09ee01b
The stack size is fixed. The linker script puts the stack section
after the bss section. The initial stack pointer is not at the
end of the RAM (as often seen).
Thus the initial stack pointer address of the main application
is different than the one from DFU. When starting the main
application the stack pointer needs to be set to the new value.
If this is not done the main application stack may overwrite the
data in bss, even without exceeding the fixed stack size.
Change-Id: Ie354d603fe302d3d5bdfa9c31575411de722323b
In the SIMtrace and QMOD schematics the LEDs are connected to +3.3V.
Thus to switch the LED on we need to set the pin low.
Change-Id: Id8cc27e6f0b6556ba5e7ea4d254dd0fe59042a0c
don't wait for space to be available in the buffer since since would
prevent from processing non-console (e.g. debug) more important data
Change-Id: Ia625b09eb30bb7b43edd3989f697d8ef33200f28
Use USART 0 connected to the SIM card side to sniff the communication.
The card side can also measure ETU times.
Do proper pin initialization.
This code can already capture the ATR communication between phone and card.
Change-Id: I0597ec723cb2225540c89c3821b91d8a45adfcd6
the curent local copies of libosmocore headers + source is a temporary
hack anyway. We should instead rely on a system-wide install of
libosmocore cross-compiled for arm-none-eabi. But leave that as a
second (later) step beyond this patch.
Change-Id: Ia63fd842d45a2b404233b4326050e7eda0604cf0
fixes following warning:
libboard/common/source/board_cstartup_gnu.c:137:11: warning: assignment to 'void (*)(void)' from 'unsigned int' makes pointer from integer without a cast [-Wint-conversion]
appReset = pSrc[1];
The original board startup script is provided by Atmel.
It has been modified to handle application or DFU booting.
The copyright notice has been updated to reflect this change.
Each board can define its own conditions on which the controller should
boot into DFU mode rather than normal application mode. Let's move the
"UART loopback jumper" to QMOD specific part. For SIMtrace we have an
actual button and can use that in a future patch.
The logic to detect if the respective module is already initialized
or not was broken. When performing initialization, we of course need
to set initialized=1.
