In dispatch_received_usb_msg(), we ran into an infinite loop if a
too long messages was received on the OUT EP. Let's break the loop.
Change-Id: I5325ed15d3dd79a42f8dac34d618e86b9334c301
Closes: OS#4429
The new SIMTRACE_MSGT_BD_CEMU_CONFIG command can be used to set/change
a bitmask of optional features that can be enabled in the simtrace
by the host software. This is useful for enabling features in the
firmware which are not supported by older host utilities.
The firmware will return the actually set/configured features in
response.
The feature bitmask is not yet used anywhere; it will be by subequent
patches.
Change-Id: I7cdd3f9171dbed45de0089defe29d2b59044bd84
So far, we called card_emu_io_statechg() from interrupt context, which
was safe with the current code. However, as we want to trigger a more
comprehensive reset of data structures, including the flushing of
message queues, it is best to shift this processing from interrupt
context to main loop context.
Change-Id: I3983078396538f32bdff55611c41d2163be4d796
Related: OS#4251
Some boards like QMOD cannot simulate a virtual card insert signal
towards the modem (as the mPCIe connector doesn't have that signal).
In these situations, we were aborting processing of the related OUT
endpoint command and forgot to release the related memory.
Change-Id: I489097b7e332004e0f2beca0b22fa36d5d1d31b5
Related: OS#4251
on the QMOD board the VCC signal from the modem is measured using
an ADC (SIMtrace board just use card detect).
the threshold to consider VCC as activated was set to 2.8V, which
gives a bit of margin for the expected 3.0V.
still, we had one board where the voltage was 2.8V.
to be resilient against lower than expected voltages from
modems (or boards), we lowered the threshold to 2.5V.
this is still save for the SAM3S to correctly identify high/low
levels.
Change-Id: Iac2778903690045e4e63fef29f812205d00c28ed
previously the card RST, VCC, and CLK signal states have been initialized with
default values corresponding to an inactive reader.
this worked fine for actual inactive readers since the default values match
and would be updated when the signal changes (edge detection).
but if the reader is in another state, card activation detection could fail.
this is fixed since the actual signal values are now used during initialisation.
at the same time I changed the variable type from uint8_t to boolean since they
have only two possible states, and understanding the actual state when coding
is simpler (no need to check which integer corresponds to which state).
this change has been successfully tested on the 2 slots of OWHW board.
Change-Id: Ie9245d75d48ae93d16f97897d4fa5ad6cd402e73
There have been tons of format-string related bugs in our code which
we never discovered due to disabling -Wformat. Let's fix that.
Change-Id: I5ec466361bcc526fac1f4897673264ee5af3458b
this changes how ATR is handled.
the ATR is also printed when set (as important debug information).
the test is also updated to correspond to the new mechanism (
simulating the timeout before sending the ATR)
Change-Id: I69df797e2feadffa9f5f977cb71b69386cee7cd0
the msg->l2h pointer was not set but used later on, e.g. in
dispatch_usb_command_cardem, case SIMTRACE_MSGT_DT_CEMU_SET_ATR):
> case SIMTRACE_MSGT_DT_CEMU_SET_ATR:
> > atr = (struct cardemu_usb_msg_set_atr *) msg->l2h;
> > card_emu_set_atr(ci->ch, atr->atr, atr->atr_len);
l2h is by default 0, thus not pointing to the actual message l2h.
I wonder how cardem worked worked before with this issue though.
Change-Id: Ifbb53dbf478d8dade82251f769e78e1306e77434
when building the trace app for the simtrace board gcc was outputing
the following error:
libboard/common/source/boardver_adc.c:20:17: warning: 'adc2uv' defined but not used [-Wunused-function]
static uint32_t adc2uv(uint16_t adc)
adc2uv is used by qmod, and defined in two places:
in boardver_adc.c and mode_cardemu.c.
this change will have adc2uv only defined in boardver_adc.c and make
available in the header to be used by mode_cardemu.c.
Change-Id: I8a772638fa8dd02d8bc8b7631de5af5a22647c55
In commit eac1bec428 we start to use the
ringbuffer inside the console printing code. As a result, we must not
use TRACE_*() or printf() from within ringbuffer.c code to avoid
infinite recursion.
Instead, let rbuf_write() return a negative return value in case the
ring buffer overflows. This way, the callers (outside the
console/stdout code) can print an error message themselves.
Change-Id: Ib009f013be119dbad22fa2b7d60ec8dee59baee5
the curent local copies of libosmocore headers + source is a temporary
hack anyway. We should instead rely on a system-wide install of
libosmocore cross-compiled for arm-none-eabi. But leave that as a
second (later) step beyond this patch.
Change-Id: Ia63fd842d45a2b404233b4326050e7eda0604cf0
msg->l2h should always point at the first byte of the header after the
generic simtrace header. For some reason this doesn't work if used
globally, but it is required for the MSGC_MODEM messages to be
interpreted correctly.
The current protocol was card-emulation specific. The new protocol is
generic/flexible enough to accommodate both tracing and card emulation,
as well as modem control and other future extensions.
We now generalize the USB communiction and abandon the 'req_ctx'
structure inherited from openpcd. Instead we use the libosmocore 'msgb'
structure to handle incoming and outgoing USB tranfers. We also use
linuxlist-based msgb-queues for each endpoint.
