mirror of
https://gitea.osmocom.org/sim-card/simtrace2.git
synced 2026-03-17 05:38:33 +03:00
f721e69bc1
Remove the paragraph about writing to the Free Software Foundation's mailing address. The FSF has changed addresses in the past, and may do so again. In 2021 this is not useful, let's rather have a bit less boilerplate at the start of source files. Change-Id: Ie0a3b2273383adbb3303faffd6ff96be7f4cae99
123 lines
3.9 KiB
C
123 lines
3.9 KiB
C
/* SIMtrace 2 common board pin definitions
|
|
*
|
|
* (C) 2015-2017 by Harald Welte <hwelte@hmw-consulting.de>
|
|
* (C) 2018, sysmocom -s.f.m.c. GmbH, Author: Kevin Redon <kredon@sysmocom.de>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*/
|
|
#ifndef _BOARD_
|
|
#define _BOARD_
|
|
|
|
/** Headers */
|
|
#include "chip.h"
|
|
/* We need this for a nop instruction in USB_HAL.c */
|
|
#define __CC_ARM
|
|
|
|
/** Board */
|
|
#include "board_lowlevel.h"
|
|
#include "uart_console.h"
|
|
#include "iso7816_4.h"
|
|
#include "led.h"
|
|
#include "cciddriver.h"
|
|
#include "usart.h"
|
|
#include "USBD.h"
|
|
|
|
#include "USBD_Config.h"
|
|
#include "USBDDriver.h"
|
|
|
|
/** Highlevel */
|
|
#include "trace.h"
|
|
#include "stdio.h"
|
|
#include "stdlib.h"
|
|
#include "string.h"
|
|
#include "inttypes.h"
|
|
#include "syscalls.h"
|
|
|
|
#define MIN(a, b) ((a < b) ? a : b)
|
|
|
|
#ifdef __GNUC__
|
|
#undef __GNUC__
|
|
#endif
|
|
|
|
/** Family definition (already defined) */
|
|
#define sam3s
|
|
/** Core definition */
|
|
#define cortexm3
|
|
|
|
/* LEDs are used to indicate the status
|
|
* the LED definition is board specific
|
|
* most boards have two LEDs, one green and one red
|
|
* the red LED indicates of the main firmware is ready (on) or if there is an error (blinking)
|
|
* the green LED indicates if the firmware is idling (on) or if there is activity (blinking)
|
|
*/
|
|
/** USART0 pin RX */
|
|
#define PIN_USART0_RXD {PIO_PA9A_URXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
|
/** USART0 pin TX */
|
|
#define PIN_USART0_TXD {PIO_PA10A_UTXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
|
|
|
#define BOARD_PIN_USART_RXD PIN_USART0_RXD
|
|
#define BOARD_PIN_USART_TXD PIN_USART0_TXD
|
|
|
|
#define BOARD_ID_USART ID_USART0
|
|
#define BOARD_USART_BASE USART0
|
|
|
|
#define PINS_UART { PIO_PA9A_URXD0|PIO_PA10A_UTXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
|
|
|
|
/** UART0 */
|
|
/** Console baud rate in bps */
|
|
#define CONSOLE_BAUDRATE 921600
|
|
/** UART peripheral used by the console (UART0). */
|
|
#define CONSOLE_UART UART0
|
|
/** UART peripheral ID used by the console (UART0). */
|
|
#define CONSOLE_ID ID_UART0
|
|
/** UART ISR used by the console (UART0). */
|
|
#define CONSOLE_ISR UART0_IrqHandler
|
|
/** UART IRQ used by the console (UART0). */
|
|
#define CONSOLE_IRQ UART0_IRQn
|
|
/** Pins description corresponding to Rxd,Txd, (UART pins) */
|
|
#define CONSOLE_PINS {PINS_UART}
|
|
|
|
/// Smartcard detection pin
|
|
// FIXME: add connect pin as iso pin...should it be periph b or interrupt oder input?
|
|
#define BOARD_ISO7816_BASE_USART USART0
|
|
#define BOARD_ISO7816_ID_USART ID_USART0
|
|
|
|
/* USART peripherals for a phone and SIM card setup */
|
|
/* USART peripheral connected to the SIM card */
|
|
#define USART_SIM USART0
|
|
/* ID of USART peripheral connected to the SIM card */
|
|
#define ID_USART_SIM ID_USART0
|
|
/* Interrupt request ID of USART peripheral connected to the SIM card */
|
|
#define IRQ_USART_SIM USART0_IRQn
|
|
/* USART peripheral connected to the phone */
|
|
#define USART_PHONE USART1
|
|
/* ID of USART peripheral connected to the phone */
|
|
#define ID_USART_PHONE ID_USART1
|
|
/* Interrupt request ID of USART peripheral connected to the phone */
|
|
#define IRQ_USART_PHONE USART1_IRQn
|
|
|
|
// Board has UDP controller
|
|
#define BOARD_USB_UDP
|
|
|
|
#define BOARD_USB_DFU
|
|
|
|
|
|
#define BOARD_DFU_BOOT_SIZE (16 * 1024)
|
|
#define BOARD_DFU_RAM_SIZE (2 * 1024)
|
|
#define BOARD_DFU_PAGE_SIZE 512
|
|
/** number of DFU interfaces (used to flash specific partitions) */
|
|
#define BOARD_DFU_NUM_IF 3
|
|
|
|
extern void board_exec_dbg_cmd(int ch);
|
|
extern void board_main_top(void);
|
|
extern int board_override_enter_dfu(void);
|
|
#endif
|