catarrh
b7a6e50fc8
The recommended tap is the short cable with external pull resistors whose pins are fixed and known in advance (D5=CLK, D0=I/O, D4=RST, D2=VCC), so the auto-detection tool is no longer needed. Drop it and all references: - Delete tools/detect_pins.py. - README: replace the 'Detecting the wiring' section with a fixed-wiring note; drop the Python/numpy prerequisite and the detect_pins capture step from the Windows guide. - setup.bat: remove the Python/numpy check and the 'find the wiring' next step.
117 lines
5.6 KiB
Batchfile
117 lines
5.6 KiB
Batchfile
@echo off
|
|
rem sigrok_iso7816_stream setup (Windows): verify sigrok-cli, register decoder.
|
|
setlocal EnableExtensions EnableDelayedExpansion
|
|
|
|
set "REPO_DIR=%~dp0"
|
|
if "%REPO_DIR:~-1%"=="\" set "REPO_DIR=%REPO_DIR:~0,-1%"
|
|
set "DEC_DIR=%LOCALAPPDATA%\libsigrokdecode\decoders"
|
|
set "LINK=%DEC_DIR%\iso7816"
|
|
|
|
echo sigrok_iso7816_stream setup (Windows)
|
|
echo.
|
|
|
|
rem ---- sigrok-cli -------------------------------------------------------
|
|
echo Checking sigrok-cli...
|
|
set "SIGROK_EXE="
|
|
if not defined SIGROK_EXE if exist "%ProgramFiles%\sigrok\sigrok-cli\sigrok-cli.exe" set "SIGROK_EXE=%ProgramFiles%\sigrok\sigrok-cli\sigrok-cli.exe"
|
|
if not defined SIGROK_EXE if exist "%ProgramFiles(x86)%\sigrok\sigrok-cli\sigrok-cli.exe" set "SIGROK_EXE=%ProgramFiles(x86)%\sigrok\sigrok-cli\sigrok-cli.exe"
|
|
if not defined SIGROK_EXE if exist "%ProgramFiles%\sigrok\PulseView\sigrok-cli.exe" set "SIGROK_EXE=%ProgramFiles%\sigrok\PulseView\sigrok-cli.exe"
|
|
if not defined SIGROK_EXE if exist "%ProgramFiles(x86)%\sigrok\PulseView\sigrok-cli.exe" set "SIGROK_EXE=%ProgramFiles(x86)%\sigrok\PulseView\sigrok-cli.exe"
|
|
if not defined SIGROK_EXE where sigrok-cli >nul 2>&1 && for /f "delims=" %%i in ('where sigrok-cli') do set "SIGROK_EXE=%%i"
|
|
if not defined SIGROK_EXE goto :notfound
|
|
for %%i in ("!SIGROK_EXE!") do set "SIGROK_DIR=%%~dpi"
|
|
if "!SIGROK_DIR:~-1!"=="\" set "SIGROK_DIR=!SIGROK_DIR:~0,-1!"
|
|
echo [ok] !SIGROK_EXE!
|
|
rem Add sigrok-cli dir to PATH so subsequent calls work even if only
|
|
rem discovered at the default install location.
|
|
set "PATH=!SIGROK_DIR!;!PATH!"
|
|
sigrok-cli --version 2>nul | findstr /r "^"
|
|
goto :sigrok_ok
|
|
|
|
:notfound
|
|
echo [X] sigrok-cli not found.
|
|
echo Searched:
|
|
echo %ProgramFiles%\sigrok\sigrok-cli
|
|
echo %ProgramFiles(x86)%\sigrok\sigrok-cli
|
|
echo %ProgramFiles%\sigrok\PulseView
|
|
echo %ProgramFiles(x86)%\sigrok\PulseView
|
|
echo PATH
|
|
echo Install it from https://sigrok.org/wiki/Downloads
|
|
echo ^(sigrok-cli-0.7.2-x86_64-installer.exe^), then re-open this
|
|
echo window so PATH changes take effect and re-run.
|
|
exit /b 1
|
|
|
|
:sigrok_ok
|
|
|
|
rem If sigrok-cli fails to start with error 0xc0150002, install the
|
|
rem Microsoft Visual C++ 2010 Redistributable (msvcr100.dll).
|
|
|
|
rem ---- firmware ---------------------------------------------------------
|
|
echo Checking fx2lafw firmware...
|
|
set "FW_FOUND="
|
|
if not defined FW_FOUND if exist "!SIGROK_DIR!\share\sigrok-firmware\fx2lafw-cypress-fx2.fw" set "FW_FOUND=!SIGROK_DIR!\share\sigrok-firmware"
|
|
if not defined FW_FOUND if exist "!SIGROK_DIR!\..\share\sigrok-firmware\fx2lafw-cypress-fx2.fw" set "FW_FOUND=!SIGROK_DIR!\..\share\sigrok-firmware"
|
|
if not defined FW_FOUND if exist "%ProgramFiles%\sigrok\sigrok-cli\share\sigrok-firmware\fx2lafw-cypress-fx2.fw" set "FW_FOUND=%ProgramFiles%\sigrok\sigrok-cli\share\sigrok-firmware"
|
|
if not defined FW_FOUND if exist "%ProgramFiles(x86)%\sigrok\sigrok-cli\share\sigrok-firmware\fx2lafw-cypress-fx2.fw" set "FW_FOUND=%ProgramFiles(x86)%\sigrok\sigrok-cli\share\sigrok-firmware"
|
|
if not defined FW_FOUND if exist "%ProgramFiles%\sigrok\PulseView\share\sigrok-firmware\fx2lafw-cypress-fx2.fw" set "FW_FOUND=%ProgramFiles%\sigrok\PulseView\share\sigrok-firmware"
|
|
if not defined FW_FOUND if exist "%ProgramFiles(x86)%\sigrok\PulseView\share\sigrok-firmware\fx2lafw-cypress-fx2.fw" set "FW_FOUND=%ProgramFiles(x86)%\sigrok\PulseView\share\sigrok-firmware"
|
|
if not defined FW_FOUND if exist "%LOCALAPPDATA%\sigrok-firmware\fx2lafw-cypress-fx2.fw" set "FW_FOUND=%LOCALAPPDATA%\sigrok-firmware"
|
|
if not defined FW_FOUND if exist "%ProgramData%\sigrok-firmware\fx2lafw-cypress-fx2.fw" set "FW_FOUND=%ProgramData%\sigrok-firmware"
|
|
if defined FW_FOUND (
|
|
echo [ok] !FW_FOUND!
|
|
) else (
|
|
echo [!] bundled firmware directory not found - continuing anyway;
|
|
echo the installer normally ships fx2lafw firmware, and libsigrok
|
|
echo also searches %LOCALAPPDATA%\sigrok-firmware
|
|
)
|
|
|
|
rem ---- decoder registration --------------------------------------------
|
|
echo Registering decoder...
|
|
if not exist "%DEC_DIR%" mkdir "%DEC_DIR%"
|
|
if exist "%LINK%\pd.py" goto :link_ok
|
|
if exist "%LINK%" rmdir "%LINK%"
|
|
mklink /J "%LINK%" "%REPO_DIR%" >nul 2>&1
|
|
if errorlevel 1 (
|
|
echo [X] could not create junction %LINK%
|
|
exit /b 1
|
|
)
|
|
:link_ok
|
|
sigrok-cli -L 2>nul | findstr /i "iso7816" >nul
|
|
if errorlevel 1 (
|
|
echo [X] decoder registered but NOT listed by sigrok-cli.
|
|
echo Expected junction: %LINK%
|
|
exit /b 1
|
|
)
|
|
echo [ok] %LINK% -^> listed by sigrok-cli
|
|
|
|
rem ---- hardware samplerate probe ---------------------------------------
|
|
echo Probing device samplerates...
|
|
set "MAX_RATE="
|
|
for %%r in (1M 2M 4M 8M 12M 16M 20M 24M) do (
|
|
sigrok-cli -d fx2lafw --config samplerate=%%r --continuous --time 20 ^
|
|
-P "iso7816:clk=D0:data=D1" >"%TEMP%\iso7816-probe.txt" 2>&1
|
|
type "%TEMP%\iso7816-probe.txt" | findstr /c:"Unable to claim" >nul && (
|
|
echo blocked - another program holds the device
|
|
set "DEVICE_MSG=1"
|
|
goto :probedone
|
|
)
|
|
type "%TEMP%\iso7816-probe.txt" | findstr /c:"Failed to open" /c:"No devices found" >nul && (
|
|
echo skipped - no FX2 device connected
|
|
set "DEVICE_MSG=1"
|
|
goto :probedone
|
|
)
|
|
type "%TEMP%\iso7816-probe.txt" | findstr /r /c:"invalid argument" /c:"Unable to sample" /c:"Could not start" >nul || set MAX_RATE=%%r
|
|
)
|
|
:probedone
|
|
if defined MAX_RATE (
|
|
echo Highest accepted samplerate: !MAX_RATE!
|
|
) else if not defined MAX_RATE if not defined DEVICE_MSG (
|
|
echo unknown - device present but no rate accepted
|
|
)
|
|
|
|
echo.
|
|
echo Done. Next steps:
|
|
echo 1. Plug GND first and verify contact manually (see README).
|
|
echo 2. start.bat -- capture + GSMTAP stream
|
|
endlocal
|