- improves trace diagnostic output by moving cursor back over the
the rotor before a diagnostic message has a chance to be printed.
there is still a race condition, but it is much better.
Change-Id: Iad7767f2a5dbbd67b0f33b9bfc2c3864ce308990
This fixes the firmware USB interface somehow getting stuck
after a USB disconnect/reconnect without power cycle.
Right now there are a number of things we only execute the first time we
reach USBD_STATE_CONFIGURED, but not at any subsequent such event.
It's also rather clear that this doesn't really show in simtrace2 as it
is bus-powered. And it doesn't show on OWHW as we don't have any USB
unplug situations of the USB between the on-board traces of USB host and
SAM3S. So this really only is relevant to QMOD.
A cheap and dirty work-around is to simply reset the entire uC every
time a USB unplug happens.
Change-Id: I6678bb2192c1419ed388b46c4ae7aa1ce18dc7ee
Related: OS#5578
the ISO7816 UARTs have highest priority, while console has lowest.
remaining sources (USB, ADC, GPIO) are in between.
Change-Id: Ie6c97d61d8da3990b6e44144f36cb6d37d194307
DFU flashing of apps sometimes aborts, and although rare this leads to
broken devices if no boot button or serial/jtag access exists, because
the bootloader will keep trying to start a half-flashed app that then
crashes at some point.
The easiest fix that works with existing bootloaders is to prepend a
small 512 byte stub that calculcates the crc and compares it with the
crc calculated at build time, and then either starts the actual app, or
sets the dfu flag and resets. This ensures we either have a working,
running app, or end up in the bootloader, ready to flash again.
For obvious reasons this only applies to dfu apps, and not to flash
targets like the actual bootloader itself.
Change-Id: Id6df0486c8b779889d21800dc2441b3aa9af8a5f
Remove the paragraph about writing to the Free Software Foundation's
mailing address. The FSF has changed addresses in the past, and may do
so again. In 2021 this is not useful, let's rather have a bit less
boilerplate at the start of source files.
Change-Id: Ie0a3b2273383adbb3303faffd6ff96be7f4cae99
The previous value was way too low and led to reenumeration issues when
switching from app to bl because the hosts are fairly lenient and
feature long delays until they accept disappearing devices as gone for
good instead of ignoring a presuambly flaky usb cable or connection.
Related: SYS5061
Change-Id: I9b8c8bf794ad5b94fc7ea2a01d1ebf4e36862c36
All the parts are DNP and never existed on the simtrace2 with sam3; the
sam3 has internal pullups that are part of the usb peripheral.
Change-Id: I04a703a2eba6ff1dc64692c089213389d0c1066d
This bl updater can be flashed as app and will update the bootloader and
then
delete itself before resetting the sam3, so the device will end up in
the newly
updated dfu bootloader afterwards, without having to press the
bootloader button
or requring any other manual interaction, ready to receive a new
application image.
Building the blupdater requires a previously built dfu-flash bootloader
bin file that
will then be embedded into the app during building.
Related: OS#1704
Related: SYS5061
Change-Id: I53dea57bba790a2ab3245d9483e0ff1c8d19d5e3
This led to occasional crashes for targets with leds since it was
introduced 3 years ago
The interesting thing is that most of the time it didn't crash...
Change-Id: Ia6a1b1fc0e44a301b4fb1d9c9fdbc27d61dcab97
This adds support for the new ngff_cardem board, a board that
basically combines a ngff breakout board with a built-in SIMtrace2.
Cardem works, but depending on the modem it might need a adjusted ATR to
ensure a lower baud rate is used by the modem, high rates might lead
to weird power cycling of the card after a few transfers.
Trace was also tested and appears to work as expected.
Change-Id: Ia96124fbe8a752c98e7fd4096d542a3b2b9bc255
Instead of using the timer/counter peripheral to handle the waiting time
and corresponding timeout, the USART peripheral internal timeout
mechanism is used.
This is particularly important for the SIMtrace board since there
(contrary to other boards) the I/O signal is not wired to a TIO pin
of the timer/counter block, and hence Rx/Tx data cannot reset that
timer/counter.
As a result of this migration, cardem is now supported not only on
owhw + qmod, but also on the simtrace board.
The guts of this change have been lifted out of Change-Id
Ibcb2c8cace9137695adf5fb3de43566f7cfb93b5 by Kevin Redon, which was
unfortunately touching various different topics at the same time and
hence was split up. Some improvements are the introduction of the
ENABLE_TX_TIMER_ONLY mode, which avoids the USART interrupt handler
getting hammered with TXRDY between release of RST and start of the ATR.
Change-Id: Ibcb2c8cace9137695adf5fb3de43566f7cfb93b5
Related: OS#1704
This reverts commit 4a58c08d67.
The code replicates to a large extent what is already present in iso7816_fidi.c
and I have serious doubts about the correctness of the computation in
its iso7816_3_calculate_wt() function.
Change-Id: I3f26da4e9aa8d7b0f4b4b7992269cf365a643ec7
We are not using any PIO interrupts from DFU mode. It's only used in
the main application firmware (verified by "git grep PIO_ConfigureIt")
Change-Id: Id1447af519df3183061f3d3f156a8dd84789af16
this adds the DFU as application, allowing to flash the bootloader.
a USB DFU alternative is added to flash the bootloader partition.
when the DFU is started as bootloader, the partition/alternative
to flash the bootloader is marked as "not available", and
ineffective.
the same happens for the application partition when DFU is started
as application.
this distinction is make at compile time, not at runtime, because
of size restrictions (the bootloader was already close to the
16 kB limit).
*_dfu_flash.bin should not be mixed with *_dfu_dfu.bin.
*_dfu_dfu.bin should be flashed as application using the already
existing DFU bootloader.
once this images is started (as application), the *_dfu_flash.bin
should be flashed as bootloader using the DFU application.
once the DFU bootloader has been flashed, soft resetting
(not re-powering) will cause the bootloader to start, allowing to
flash the application with a normal image (e.g. not DFU),
replacing the DFU application.
this switch to DFU only happens after downloading (e.g. flashing).
it is planned to have the DFU application erase itself after
flashing, but this is currently not implemented.
Change-Id: Ic273bb593a7669111b0219fe301d7897419167c8
In the end we want to share most of this, irrespective of the "APP".
Let's avoid unnecessary differences.
Change-Id: Icf063d4ca79edf66ffbe8e87a915deb77dec478a
This unifies the printing of the welcome banner, and it also ensures
that all modes print all information (serial number, reset cause).
Furthermore the APP and BOARD #defines from the make environment are
also printed.
Change-Id: I7e6bc05cee4b9ec0fd9a05dc90ce0b26a5763e5a
the USB trace now respects the global setting.
the verbosity is also decreased, not showing USB activity unless
debugging.
this also saves some space.
the reset cause is now printed.
the strings increase the bootloader size, but it already exceeded
the 16 kB limit when trace level is set to info.
Change-Id: I9ba08d4bb4f188f6e7a202ea86acb7a42a2054f3
"SIMtrace 2 compatible device" is pretty generic. Let's have the
actual board name inside the string descriptors, giving a more
user friendly experience in case users are issuing 'lsusb' and the
like.
Change-Id: Ibcc338b504bd2a1605e31d7f5eadb7161f547c6a
This string dates back to some very early naming; let's reflect how
we have been calling this in reality for quite some time now.
Change-Id: I5a7497188385706a1e924784073c619fa9bfdd60
when starting the DFU bootloader, but USB configuration (e.g.
enumeration) failed, the MCU restarted in the main application.
this occured after a DFU detach and were the USB host missed the
USB reset.
now after MCU reset, the bootloader is started again, since this
is what was requested to begin with.
the bootloader will always restart in the bootloader until USB
enumeration succeeded.
this boot loop can be stopped by unplugging/removing power from
the device.
Change-Id: I4062a7d8a7934af2119c169759b614dc45990651
the specification requires a reset duration of at least 10 ms.
reset is indicated by the device to the host by removing the
pull-up on D+ (host to device reset is a USB packet).
we used 20 ms, but on some setups (USB host, stack, hub, and load
dependent), this does not seem to be enough (no USB enumeration
was performed afterward, at least for the DFU bootloader).
increasing to 50 ms solved the issue on the affected setups.
instead of USB suspend, the more proper USB disconnect is used.
this mainly disables the pull-up provided by the USB peripheral.
USB activate is not required since the follow up initialisation
takes care of it.
Change-Id: If5ceb3b8f7a8f134d4439fdd138dd12b46589f97
the longer output is to fast and often incomplete.
the shorter version is enough to view the progress when not
debugging.
Change-Id: I97bb84da68d1f3bc14fb7c05400edf1748f55460
The freq_ctr app is a small application that is implementing a
simplistic direct-mode frequency counter using the internal 32.768kHz
oscillator and two TC blocks. One of them is used to generate a 1Hz
signal, which is then subsequently used by the other TC to trigger
a counter read after exactly 1s.
This is in itself not something useful on a simtrace2 device. However,
it is a separate 'app' and I prefer to have the code here in master
over some obscure branch that's easy to forget about.
Change-Id: I2249bfb8dd6a88d85d406f3b33537377133d0939
There have been tons of format-string related bugs in our code which
we never discovered due to disabling -Wformat. Let's fix that.
Change-Id: I5ec466361bcc526fac1f4897673264ee5af3458b
USB reset can be signaled by pulling low USB D+ for at least 10 ms,
according to the USB specification. This force a re-enumeration.
This time is increased to 20 ms to work with more USB HUBs.
Some SAM3S based board have external D+ pull-up mechanism (such as
SIMtrace) which needs to be used to pull D+ low.
This is a legacy mechanism from SAM7S history.
This mechanism is not required anymore on the SAM3S, and the qmod
does not use it. When the USB HAL is suspended, the transceiver is
disabled, causing D+ and D- to be pulled low. Then the HAL is activated
again. This is particularly required when DFU is started (and
enumerated), and after flashing the SAM3S switched to the main
application (without reset), so it can properly re-enumerate.
This board difference is now defined on the board header.
Change-Id: I9b58d8101c2fcf5595026b675728826af26127a3
a lot of the procedures are done in ISRs, but the watchdog is only
reset in the main loop.
this causes frequent reset, particularly at the beginning were
states have to the initialized.
Change-Id: Iad364444fca9d18f9a8cf47d5e0840ccd7bac2ef
The red and green LEDs are now used as follows:
- red on = power (firmware is running)
- red blink = error detected (e.g. during ISO-7816 parsing)
- green on = running (sniffer mode is running)
- green blink = activity (e.g. USB message sent)
Change-Id: Ib1b6ff87fb92d6ed3ecae4bc89386206aaab508e
TRACE_INFO will also provide the DFU start reason, but TRACE_INFO
(TRACE_LEVEL >= 4) should only be used for debugging.
WARNING: With TRACE_LEVEL >= 4 the DFU binary is over the maximum of
16 kiB allocated for the DFU bootloader.
Thus make combined will not boot the main application because its
start if after the expecte 16 kiB address; and flashing using DFU
will overwrite the DFU bootloader itself.
Change-Id: I82323e0f76c03f67df7dc8f2b6783166cc25f3aa
Use USART 0 connected to the SIM card side to sniff the communication.
The card side can also measure ETU times.
Do proper pin initialization.
This code can already capture the ATR communication between phone and card.
Change-Id: I0597ec723cb2225540c89c3821b91d8a45adfcd6
