Add device profile for Arduino logic analyzer

Use this device profile with the alternative SUMP client.  It goes in
the plugins directory with the other similarly named files.

README

@@ -5,29 +5,26 @@ This Arduino sketch implements a SUMP protocol compatible with the standard
 SUMP client as well as the alternative client from here:
 	http://www.lxtreme.nl/ols/
 
-The alternative client version is highly recommended.  Download version
-"ols-0.9.7" or newer for built-in device profiles.
-
 This SUMP protocol compatible logic analyzer for the Arduino board supports
 5 channels consisting of digital pins 8-12, which are the first 5 bits (0-4)
 of PORTB. Arduino pin 13 / bit 5 is the Arduino LED, bits 6 & 7 are the
 crystal oscillator pins.
-
 Uncomment CHAN5 below if you want to use the LED pin as an input and have
 6 channels.
 
-On the Arduino Mega board 8 channels are supported and 7k of samples.
+NOTE:
-Pins 22-29 (Port A) are used by default.
+You must DISABLE the Arduino auto reset feature to use this logic analyzer
+code. There are various methods to do this, some boards have a jumper,
+others require you to cut a trace.  You may also install a *precisely*
+120 Ohm resistor between the reset & 5V piins.  Make sure it is really
+120 Ohm or you may damage your board.
 
 To use this with the original or alternative SUMP clients,
 use these settings:
 
-Sampling rate: 4MHz (or lower) (no 2MHz on ATmega168)
+Sampling rate: 1MHz (or lower)
 Channel Groups: 0 (zero) only
-Recording Size:
+Recording Size: 1024 (or lower)
-   ATmega168:  532 (or lower)
-   ATmega328:  1024 (or lower)
-   ATmega2560: 7168 (or lower)
 Noise Filter: doesn't matter
 RLE: disabled (unchecked)
 
@@ -36,38 +33,5 @@ below 1MHz.  1MHz works for a basic busy wait trigger that doesn't store
 until after the trigger fires.
 Please try it out and report back.
 
-Older Notes
+Release: v0.03 March 7, 2011.
-===========================================================================
-NOTE: With v0.11 you can now sample at 4MHz & 2MHz rates in addition to the 
-      previous 1MHz and lower rates.  This is done via unrolled loops which
-      makes the source code huge and the binary takes much more of the flash.
-      v0.11 is just slightly to big for an ATmega168's flash.  You can comment
-      out either captureInline2mhz() or captureInline4mhz() and it will fit.
-      [ The code automatically skips the 2MHz code now, this isn't needed. ]
-
-NOTE: v0.09 switched the channels BACK to pins 8-13 for trigger reliability.
-      Please report any issues.  Uncomment USE_PORTD for pins 2-7.
-
-NOTE: The device profiles should be included with this code.  Copy them to the
-      'plugins' directory of the client.  The location varies depending on the
-      platform, but on the mac it is here by default:
-      /Applications/LogicSniffer.app/Contents/Resources/Java/plugins
-      [ These are included in ols-0.9.7 or newer so do not copy them. ]
-
-NOTE: If you are using the original SUMP client, then you will get a
-      "device not found" error.
-      You must DISABLE the Arduino auto reset feature to use this logic analyzer
-      code. There are various methods to do this, some boards have a jumper,
-      others require you to cut a trace.  You may also install a *precisely*
-      120 Ohm resistor between the reset & 5V piins.  Make sure it is really
-      120 Ohm or you may damage your board.  It is much easier to use the
-      alternative SUMP client referenced above.
-      [ This is not needed with ols-0.9.7 or newer. ]
-      [ DO NOT use this resistor unless absolutely necessary on old clients. ]
-
-NOTE: This master branch now supports Arduino 1.0 only.
-      Checkout branch logic_analyzer_v0_5 for Arduino 22 support.
-
-
-Release: v0.12 September 6, 2013.
 

logic_analyzer.pde

@@ -2,7 +2,7 @@
  *
  * SUMP Protocol Implementation for Arduino boards.
  *
- * Copyright (c) 2011,2012,2013,2014 Andrew Gillham
+ * Copyright (c) 2011 Andrew Gillham
  * All rights reserved.
  *
  * Redistribution and use in source and binary forms, with or without
@@ -25,44 +25,40 @@
  * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
  * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
+ *	$Id: logic_analyzer.pde,v 1.14 2011-03-08 07:14:42 gillham Exp $
  *
  */
 
 /*
- * NOTE: v0.09 switched the channels BACK to pins 8-13 for trigger reliability.
- *       Please report any issues.  Uncomment USE_PORTD for pins 2-7.
- *
- * This Arduino sketch implements a SUMP protocol compatible with the standard
- * SUMP client as well as the alternative client from here:
- *	http://www.lxtreme.nl/ols/
- *
  * This SUMP protocol compatible logic analyzer for the Arduino board supports
- * 6 channels consisting of digital pins 2-7, which are the last 6 bits (2-7)
+ * 5 channels consisting of digital pins 8-12, which are the first 5 bits (0-4)
- * of PORTD.  Bits 0 & 1 are the UART RX/TX pins.
+ * of PORTB. Arduino pin 13 / bit 5 is the Arduino LED, bits 6 & 7 are the
+ * crystal oscillator pins.
+ * Uncomment CHAN5 below if you want to use the LED pin as an input and have
+ * 6 channels.
  *
- * On the Arduino Mega board 8 channels are supported and 7k of samples.
+ * NOTE:
- * Pins 22-29 (Port A) are used by default, you can change the 'CHANPIN' below
+ * You must DISABLE the Arduino auto reset feature to use this logic analyzer
- * if something else works better for you.
+ * code. There are various methods to do this, some boards have a jumper,
+ * others require you to cut a trace.  You may also install a *precisely*
+ * 120 Ohm resistor between the reset & 5V piins.  Make sure it is really
+ * 120 Ohm or you may damage your board.
  *
  * To use this with the original or alternative SUMP clients,
  * use these settings:
  * 
- * Sampling rate: 4MHz (or lower) (no 2MHz on ATmega168)
+ * Sampling rate: 1MHz (or lower)
  * Channel Groups: 0 (zero) only
- * Recording Size:
+ * Recording Size: 1024 (or lower)
- *    ATmega168:  532 (or lower)
- *    ATmega328:  1024 (or lower)
- *    ATmega2560: 7168 (or lower)
  * Noise Filter: doesn't matter
  * RLE: disabled (unchecked)
- *    NOTE: Preliminary RLE support for 50Hz or less exists, please test it.
  *
  * Triggering is still a work in progress, but generally works for samples
  * below 1MHz.  1MHz works for a basic busy wait trigger that doesn't store
  * until after the trigger fires.
  * Please try it out and report back.
  *
- * Release: v0.12 September 6, 2013.
+ * Release: v0.02 February 28, 2011.
  *
  */
 
@@ -82,62 +78,16 @@ void get_metadata(void);
 void debugprint(void);
 void debugdump(void);
 
-
 /*
- * Should we use PORTD or PORTB?  (default is PORTB)
+ * Uncomment CHAN5 to use it as an additional input.
- * PORTD support with triggers seems to work but needs more testing.
+ * You'll need to change the number of channels in the device profile as well.
  */
-//#define USE_PORTD 1
-#if defined(USE_PORTD)
-#define SHIFTBITS 2
-#elif defined(__AVR_ATmega32U4__)
-#define SHIFTBITS 1
-#endif
-
-/*
- * Arduino device profile:      ols.profile-agla.cfg
- * Arduino Mega device profile: ols.profile-aglam.cfg
- */
-#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-#define CHANPIN PINA
-#define CHAN0 22
-#define CHAN1 23
-#define CHAN2 24
-#define CHAN3 25
-#define CHAN4 26
-#define CHAN5 27
-#define CHAN6 28
-#define CHAN7 29
-#else
-#if defined(USE_PORTD)
-#define CHANPIN PIND
-#define CHAN0 2
-#define CHAN1 3
-#define CHAN2 4
-#define CHAN3 5
-#define CHAN4 6
-#define CHAN5 7
-#else
-#define CHANPIN PINB
-#if defined(__AVR_ATmega32U4__)
-#define CHAN0 SCK
-#define CHAN1 MOSI
-#define CHAN2 MISO
-#define CHAN3 8
-#define CHAN4 9
-#define CHAN5 10
-#define CHAN6 11
-#else
 #define CHAN0 8
 #define CHAN1 9
 #define CHAN2 10
 #define CHAN3 11
 #define CHAN4 12
-/* Comment out CHAN5 if you don't want to use the LED pin for an input */
+//#define CHAN5 13
-#define CHAN5 13
-#endif /* AVR_ATmega32U4 */
-#endif /* USE_PORTD */
-#endif /* Mega1280 or Mega2560 */
 #define ledPin 13
 
 /* XON/XOFF are not supported. */
@@ -152,48 +102,24 @@ void debugdump(void);
 #define SUMP_TRIGGER_VALUES 0xC1
 #define SUMP_TRIGGER_CONFIG 0xC2
 
-/* Most flags (except RLE) are ignored. */
+/* flags are ignored. */
 #define SUMP_SET_DIVIDER 0x80
 #define SUMP_SET_READ_DELAY_COUNT 0x81
 #define SUMP_SET_FLAGS 0x82
-#define SUMP_SET_RLE 0x0100
 
 /* extended commands -- self-test unsupported, but metadata is returned. */
 #define SUMP_SELF_TEST 0x03
 #define SUMP_GET_METADATA 0x04
 
-/* ATmega168:  532 (or lower)
+/*
- * ATmega328:  1024 (or lower)
+ * Capture size of 1024 bytes works on the ATmega328.
- * ATmega2560: 7168 (or lower)
+ *
  */
-#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-#define DEBUG_CAPTURE_SIZE 7168
-#define CAPTURE_SIZE 7168
-#elif defined(__AVR_ATmega32U4__)
-#define DEBUG_CAPTURE_SIZE 1536
-#define CAPTURE_SIZE 1536
-#elif defined(__AVR_ATmega328P__)
-#define DEBUG_CAPTURE_SIZE 1024
-#define CAPTURE_SIZE 1024
-#else
-#define DEBUG_CAPTURE_SIZE 532
-#define CAPTURE_SIZE 532
-#endif
-
-#ifdef USE_PORTD
-#define DEBUG_ENABLE DDRB = DDRB | B00000001
-#define DEBUG_ON PORTB = B00000001
-#define DEBUG_OFF PORTB = B00000000
-#else
-#define DEBUG_ENABLE DDRD = DDRD | B10000000
-#define DEBUG_ON PORTD = B10000000
-#define DEBUG_OFF PORTD = B00000000
-#endif
 #define DEBUG
 #ifdef DEBUG
-#define MAX_CAPTURE_SIZE DEBUG_CAPTURE_SIZE
+#define MAX_CAPTURE_SIZE 1024
 #else
-#define MAX_CAPTURE_SIZE CAPTURE_SIZE
+#define MAX_CAPTURE_SIZE 1024
 #endif /* DEBUG */
 
 /*
@@ -218,23 +144,18 @@ unsigned int trigger_values = 0;
 unsigned int useMicro = 0;
 unsigned int delayTime = 0;
 unsigned long divider = 0;
-boolean rleEnabled = 0;
 
 void setup()
 {
   Serial.begin(115200);
-  while (!Serial) {
-    ; // wait for serial port to connect. Needed for Leonardo only
-  }
-
 
   /*
-   * set debug pin (digital pin 8) to output right away so it settles.
+   * set debug pin to output right away so it settles.
    * this gets toggled during sampling as a way to measure
    * the sample time.  this is used during development to
    * properly pad out the sampling routines.
    */
-  DEBUG_ENABLE; /* debug measurement pin */
+  DDRD = DDRD | B10000000; /* debug measurement pin */
 
   pinMode(CHAN0, INPUT);
   pinMode(CHAN1, INPUT);
@@ -243,41 +164,9 @@ void setup()
   pinMode(CHAN4, INPUT);
 #ifdef CHAN5
   pinMode(CHAN5, INPUT);
-#endif
+#else
-#ifdef CHAN6
-  pinMode(CHAN6, INPUT);
-#endif
-#ifdef CHAN7
-  pinMode(CHAN7, INPUT);
-#endif
-#ifndef CHAN5
   pinMode(ledPin, OUTPUT);
-#endif
+#endif /* CHAN5 */
-
-#if 0
-
-  /*
-   * This sets up timer2 at 100KHz to toggle a pin.  This is useful
-   * for debugging as it gives an internally precise signal source.
-   * This doesn't work on the Arduino Mega.  Use on the Uno or older.
-   * We're using the same clock source for the timer & our sampling.
-   */
-
-  /* Set OC2A (digital pin 11) to output so we can toggle it. */
-  pinMode(11, OUTPUT);
-
-  /* reset timer to zero */
-  TCNT2 = 0;
-  TCCR2A = 0;
-  TCCR2B = 0;
-  OCR2A = 0;
-
-  /* Set CTC mode and toggle on compare. */
-  TCCR2A = _BV (COM2A0) | _BV (WGM21);
-  /* 79 = 100KHz, 15 = 500KHz, 7 = 1MHz */
-  OCR2A = 79;
-  TCCR2B = _BV (CS20);
-#endif
 }
 
 void loop()
@@ -296,10 +185,10 @@ void loop()
       break;
     case SUMP_QUERY:
       /* return the expected bytes. */
-      Serial.write('1');
+      Serial.print('1', BYTE);
-      Serial.write('A');
+      Serial.print('A', BYTE);
-      Serial.write('L');
+      Serial.print('L', BYTE);
-      Serial.write('S');
+      Serial.print('S', BYTE);
       break;
     case SUMP_ARM:
       /*
@@ -315,18 +204,7 @@ void loop()
        * so in that case (delayTime == 1 and triggers enabled) use
        * captureMicro() instead of triggerMicro().
        */
-
+      if (useMicro) {
-      if (divider == 24) {
-        /* 4.0MHz */
-        captureInline4mhz();
-      } 
-      else if (divider == 49) {
-        /* 2.0MHz */
-#if defined(__AVR_ATmega168P__)
-        captureInline2mhz();
-#endif
-      } 
-      else if (useMicro) {
         if (trigger && (delayTime != 1)) {
           triggerMicro();
         } 
@@ -344,11 +222,7 @@ void loop()
        * we can just use it directly as our trigger mask.
        */
       getCmd();
-#ifdef SHIFTBITS
-      trigger = cmdBytes[0] << SHIFTBITS;
-#else
       trigger = cmdBytes[0];
-#endif
       break;
     case SUMP_TRIGGER_VALUES:
       /*
@@ -356,11 +230,7 @@ void loop()
        * defines whether we're looking for it to be high or low.
        */
       getCmd();
-#ifdef SHIFTBITS
-      trigger_values = cmdBytes[0] << SHIFTBITS;
-#else
       trigger_values = cmdBytes[0];
-#endif
       break;
     case SUMP_TRIGGER_CONFIG:
       /* read the rest of the command bytes, but ignore them. */
@@ -399,9 +269,8 @@ void loop()
         delayCount = MAX_CAPTURE_SIZE;
       break;
     case SUMP_SET_FLAGS:
-      /* read the rest of the command bytes and check if RLE is enabled. */
+      /* read the rest of the command bytes, but ignore them. */
       getCmd();
-      rleEnabled = ((cmdBytes[1] & B1000000) != 0);
       break;
     case SUMP_GET_METADATA:
       /*
@@ -434,7 +303,9 @@ void loop()
        * you can use the Arduino serial monitor and send a '1' and get
        * a debug printout.  useless except for development.
        */
+#ifndef CHAN5
       blinkled();
+#endif /* !CHAN5 */
       debugprint();
       break;
     case '2':
@@ -451,12 +322,14 @@ void loop()
   }
 }
 
+#ifndef CHAN5
 void blinkled() {
   digitalWrite(ledPin, HIGH);
   delay(200);
   digitalWrite(ledPin, LOW);
   delay(200);
 }
+#endif /* !CHAN5 */
 
 /*
  * Extended SUMP commands are 5 bytes.  A command byte followed by 4 bytes
@@ -500,14 +373,14 @@ void getCmd() {
  */
 
 void captureMicro() {
-  unsigned int i;
+  int i;
 
   /*
-   * basic trigger, wait until all trigger conditions are met on port.
+   * basic trigger, wait until all trigger conditions are met on port B.
    * this needs further testing, but basic tests work as expected.
    */
   if (trigger) {
-    while ((trigger_values ^ CHANPIN) & trigger);
+    while ((trigger_values ^ PINB) & trigger);
   }
 
   /*
@@ -522,41 +395,39 @@ void captureMicro() {
    * this is used during development to measure the sample intervals.
    * it is best to just leave the toggling in place so we don't alter
    * any timing unexpectedly.
-   * Arduino digital pin 8 is being used here.
+   * Arduino pin 7 is being used here.
    */
-  DEBUG_ENABLE;
+  DDRD = DDRD | B10000000;
-#ifdef DEBUG
+  PORTD = B10000000;
-  DEBUG_ON;
   delayMicroseconds(20);
-  DEBUG_OFF;
+  PORTD = B00000000;
   delayMicroseconds(20);
-  DEBUG_ON;
+  PORTD = B10000000;
   delayMicroseconds(20);
-  DEBUG_OFF;
+  PORTD = B00000000;
   delayMicroseconds(20);
-#endif
 
   if (delayTime == 1) {
     /*
      * 1MHz sample rate = 1 uS delay so we can't use delayMicroseconds
      * since our loop takes some time.  The delay is padded out by hand.
      */
-    DEBUG_ON; /* debug timing measurement */
+    PORTD = B10000000; /* debug timing measurement */
     for (i = 0 ; i < readCount; i++) {
-      logicdata[i] = CHANPIN;
+      logicdata[i] = PINB;
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
     }
-    DEBUG_OFF; /* debug timing measurement */
+    PORTD = B00000000; /* debug timing measurement */
   } 
   else if (delayTime == 2) {
     /*
      * 500KHz sample rate = 2 uS delay, still pretty fast so we pad this
      * one by hand too.
      */
-    DEBUG_ON; /* debug timing measurement */
+    PORTD = B10000000; /* debug timing measurement */
     for (i = 0 ; i < readCount; i++) {
-      logicdata[i] = CHANPIN;
+      logicdata[i] = PINB;
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
@@ -564,7 +435,7 @@ void captureMicro() {
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
     }
-    DEBUG_OFF; /* debug timing measurement */
+    PORTD = B00000000; /* debug timing measurement */
   } 
   else {
     /*
@@ -573,13 +444,13 @@ void captureMicro() {
      * a better logic analyzer)
      * start of real measurement
      */
-    DEBUG_ON; /* debug timing measurement */
+    PORTD = B10000000; /* debug timing measurement */
     for (i = 0 ; i < readCount; i++) {
-      logicdata[i] = CHANPIN;
+      logicdata[i] = PINB;
       delayMicroseconds(delayTime - 1);
       __asm__("nop\n\t""nop\n\t");
     }
-    DEBUG_OFF; /* debug timing measurement */
+    PORTD = B00000000; /* debug timing measurement */
   }
 
   /* re-enable interrupts now that we're done sampling. */
@@ -590,11 +461,7 @@ void captureMicro() {
    * is done for any triggers, this is effectively the 0/100 buffer split.
    */
   for (i = 0 ; i < readCount; i++) {
-#ifdef SHIFTBITS
+    Serial.print(logicdata[i], BYTE);
-    Serial.write(logicdata[i] >> SHIFTBITS);
-#else
-    Serial.write(logicdata[i]);
-#endif
   }
 }
 
@@ -616,60 +483,21 @@ void captureMicro() {
  * this basic functionality.
  */
 void captureMilli() {
-  unsigned int i = 0;
+  int i;
 
-  if(rleEnabled) {
+  /*
-    /*
+   * very basic trigger, just like in captureMicros() above.
-     * very basic trigger, just like in captureMicros() above.
+   */
-     */
+  if (trigger) {
-    if (trigger) {
+    while ((trigger_values ^ PINB) & trigger);
-      while ((trigger_values ^ (CHANPIN & B01111111)) & trigger);
+  }
-    }
 
-    byte lastSample = 0;
+  for (i = 0 ; i < readCount; i++) {
-    byte sampleCount = 0;
+    logicdata[i] = PINB;
-
+    delay(delayTime);
-    while(i < readCount) {
-      /*
-       * Implementation of the RLE unlimited protocol: timings might be off a little
-       */
-      if(lastSample == (CHANPIN & B01111111) && sampleCount < 127) {
-        sampleCount++;
-        delay(delayTime);
-        continue;
-      }
-      if(sampleCount != 0) {
-        logicdata[i] = B10000000 | sampleCount;
-        sampleCount = 0;
-        i++;
-        continue;
-      }
-      logicdata[i] = (CHANPIN & B01111111);
-      lastSample = (CHANPIN & B01111111);
-      delay(delayTime);
-
-      i++;
-    }
-  } 
-  else {
-    /*
-     * very basic trigger, just like in captureMicros() above.
-     */
-    if (trigger) {
-      while ((trigger_values ^ CHANPIN) & trigger);
-    }
-
-    for (i = 0 ; i < readCount; i++) {
-      logicdata[i] = CHANPIN;
-      delay(delayTime);
-    }
   }
   for (i = 0 ; i < readCount; i++) {
-#ifdef SHIFTBITS
+    Serial.print(logicdata[i], BYTE);
-    Serial.write(logicdata[i] >> SHIFTBITS);
-#else
-    Serial.write(logicdata[i]);
-#endif
   }
 }
 
@@ -682,7 +510,7 @@ void captureMilli() {
  * 
  */
 void triggerMicro() {
-  unsigned int i = 0;
+  int i = 0;
 
   logicIndex = 0;
   triggerIndex = 0;
@@ -699,19 +527,17 @@ void triggerMicro() {
    * this is used during development to measure the sample intervals.
    * it is best to just leave the toggling in place so we don't alter
    * any timing unexpectedly.
-   * Arduino digital pin 8 is being used here.
+   * Arduino pin 7 is being used here.
    */
-  DEBUG_ENABLE;
+  DDRD = DDRD | B10000000;
-#ifdef DEBUG
+  PORTD = B10000000;
-  DEBUG_ON;
   delayMicroseconds(20);
-  DEBUG_OFF;
+  PORTD = B00000000;
   delayMicroseconds(20);
-  DEBUG_ON;
+  PORTD = B10000000;
   delayMicroseconds(20);
-  DEBUG_OFF;
+  PORTD = B00000000;
   delayMicroseconds(20);
-#endif
 
   if (delayTime == 1) {
     /*
@@ -731,13 +557,13 @@ void triggerMicro() {
     /*
      * 500KHz case.  We should be able to manage this in time.
      *
-     * busy loop reading CHANPIN until we trigger.
+     * busy loop reading PINB until we trigger.
      * we always start capturing at the start of the buffer
      * and use it as a circular buffer
      */
-    DEBUG_ON; /* debug timing measurement */
+    PORTD = B10000000; /* debug timing measurement */
-    while ((trigger_values ^ (logicdata[logicIndex] = CHANPIN)) & trigger) {
+    while ((trigger_values ^ (logicdata[logicIndex] = PINB)) & trigger) {
-      /* DEBUG_OFF; */
+      /* PORTD = B00000000; */
       /* increment index. */
       logicIndex++;
       if (logicIndex >= readCount) {
@@ -749,11 +575,11 @@ void triggerMicro() {
        * __asm__("nop\n\t""nop\n\t""nop\n\t");
        */
       __asm__("nop\n\t");
-      /* DEBUG_ON; */
+      /* PORTD = B10000000; */
     }
     /* this pads the immediate trigger case to 2.0 uS, just as an example. */
     __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
-    DEBUG_OFF; /* debug timing measurement */
+    PORTD = B00000000; /* debug timing measurement */
 
     /* 
      * One sample size delay. ends up being 2 uS combined with assignment
@@ -768,7 +594,7 @@ void triggerMicro() {
     triggerIndex = logicIndex;
 
     /* keep sampling for delayCount after trigger */
-    DEBUG_ON; /* debug timing measurement */
+    PORTD = B10000000; /* debug timing measurement */
     /*
      * this is currently taking:
      * 1025.5 uS for 512 samples. (512 samples, 0/100 split)
@@ -778,12 +604,12 @@ void triggerMicro() {
       if (logicIndex >= readCount) {
         logicIndex = 0;
       }
-      logicdata[logicIndex++] = CHANPIN;
+      logicdata[logicIndex++] = PINB;
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
     }
-    DEBUG_OFF; /* debug timing measurement */
+    PORTD = B00000000; /* debug timing measurement */
     delayMicroseconds(100);
   } 
   else {
@@ -791,28 +617,22 @@ void triggerMicro() {
      * Less than 500KHz case.  This uses delayMicroseconds() and some padding
      * to get precise timing, at least for the after trigger samples.
      *
-     * busy loop reading CHANPIN until we trigger.
+     * busy loop reading PINB until we trigger.
      * we always start capturing at the start of the buffer
      * and use it as a circular buffer
      *
      */
-    DEBUG_ON; /* debug timing measurement */
+    PORTD = B10000000; /* debug timing measurement */
-    while ((trigger_values ^ (logicdata[logicIndex] = CHANPIN)) & trigger) {
+    while ((trigger_values ^ (logicdata[logicIndex] = PINB)) & trigger) {
-      /* DEBUG_OFF; */
+      /* PORTD = B00000000; */
       /* increment index. */
       logicIndex++;
       if (logicIndex >= readCount) {
         logicIndex = 0;
       }
-      else {
+      /* PORTD = B10000000; */
-        /* pad the same number of cycles as the above assignment (needs verification) */
-        __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
-      }
-      delayMicroseconds(delayTime - 3);
-      __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t""nop\n\t");
-      /* DEBUG_ON; */
     }
-    DEBUG_OFF; /* debug timing measurement */
+    PORTD = B00000000; /* debug timing measurement */
 
     /* 'logicIndex' now points to trigger sample, keep track of it */
     triggerIndex = logicIndex;
@@ -821,24 +641,21 @@ void triggerMicro() {
      * This needs adjustment so that we have the right spacing between the
      * before trigger samples and the after trigger samples.
      */
-    delayMicroseconds(delayTime - 2);
+    delayMicroseconds(delayTime);
-    __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
-    __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
-    __asm__("nop\n\t""nop\n\t""nop\n\t");
 
     /* keep sampling for delayCount after trigger */
-    DEBUG_ON; /* debug timing measurement */
+    PORTD = B10000000; /* debug timing measurement */
     for (i = 0 ; i < delayCount; i++) {
       if (logicIndex >= readCount) {
         logicIndex = 0;
       }
-      logicdata[logicIndex++] = CHANPIN;
+      logicdata[logicIndex++] = PINB;
       delayMicroseconds(delayTime - 3);
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t");
     }
-    DEBUG_OFF; /* debug timing measurement */
+    PORTD = B00000000; /* debug timing measurement */
     delayMicroseconds(100);
   }
 
@@ -859,11 +676,7 @@ void triggerMicro() {
     if (logicIndex >= readCount) {
       logicIndex = 0;
     }
-#ifdef SHIFTBITS
+    Serial.print(logicdata[logicIndex++], BYTE);
-    Serial.write(logicdata[logicIndex++] >> SHIFTBITS);
-#else
-    Serial.write(logicdata[logicIndex++]);
-#endif
   }
 }
 
@@ -899,75 +712,43 @@ void setupDelay() {
  */
 void get_metadata() {
   /* device name */
-  Serial.write((uint8_t)0x01);
+  Serial.print(0x01, BYTE);
-  Serial.write('A');
+  Serial.print('A', BYTE);
-  Serial.write('G');
+  Serial.print('G', BYTE);
-  Serial.write('L');
+  Serial.print('L', BYTE);
-  Serial.write('A');
+  Serial.print('A', BYTE);
-#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
+  Serial.print('v', BYTE);
-  Serial.write('M');
+  Serial.print('0', BYTE);
-#elif defined(__AVR_ATmega32U4__)
+  Serial.print(0x00, BYTE);
-  Serial.write('L');
-#endif /* Mega */
-  Serial.write('v');
-  Serial.write('0');
-  Serial.write((uint8_t)0x00);
 
-  /* firmware version */
+  /* sample memory (1024) */
-  Serial.write((uint8_t)0x02);
+  Serial.print(0x21, BYTE);
-  Serial.write('0');
+  Serial.print(0x00, BYTE);
-  Serial.write('.');
+  Serial.print(0x00, BYTE);
-  Serial.write('1');
+  Serial.print(0x04, BYTE);
-  Serial.write('2');
+  Serial.print(0x00, BYTE);
-  Serial.write((uint8_t)0x00);
 
-  /* sample memory */
+  /* sample rate (1MHz) */
-  Serial.write((uint8_t)0x21);
+  Serial.print(0x23, BYTE);
-  Serial.write((uint8_t)0x00);
+  Serial.print(0x00, BYTE);
-  Serial.write((uint8_t)0x00);
+  Serial.print(0x0F, BYTE);
-#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
+  Serial.print(0x42, BYTE);
-  /* 7168 bytes */
+  Serial.print(0x40, BYTE);
-  Serial.write((uint8_t)0x1C);
+
-  Serial.write((uint8_t)0x00);
+  /* number of probes (5 by default) */
-#elif defined(__AVR_ATmega32U4__)
+  Serial.print(0x40, BYTE);
-  /* 1024 bytes */
+#ifdef CHAN5
-  Serial.write((uint8_t)0x04);
+  Serial.print(0x06, BYTE);
-  Serial.write((uint8_t)0x00);
-#elif defined(__AVR_ATmega328P__)
-  /* 1024 bytes */
-  Serial.write((uint8_t)0x04);
-  Serial.write((uint8_t)0x00);
 #else
-  /* 532 bytes */
+  Serial.print(0x05, BYTE);
-  Serial.write((uint8_t)0x02);
+#endif /* CHAN5 */
-  Serial.write((uint8_t)0x14);
-#endif /* Mega */
-
-  /* sample rate (4MHz) */
-  Serial.write((uint8_t)0x23);
-  Serial.write((uint8_t)0x00);
-  Serial.write((uint8_t)0x3D);
-  Serial.write((uint8_t)0x09);
-  Serial.write((uint8_t)0x00);
-
-  /* number of probes (6 by default on Arduino, 8 on Mega) */
-  Serial.write((uint8_t)0x40);
-#ifdef CHAN7
-  Serial.write((uint8_t)0x08);
-#elif CHAN6
-  Serial.write((uint8_t)0x07);
-#elif CHAN5
-  Serial.write((uint8_t)0x06);
-#else
-  Serial.write((uint8_t)0x05);
-#endif
 
   /* protocol version (2) */
-  Serial.write((uint8_t)0x41);
+  Serial.print(0x41, BYTE);
-  Serial.write((uint8_t)0x02);
+  Serial.print(0x02, BYTE);
 
   /* end of data */
-  Serial.write((uint8_t)0x00);  
+  Serial.print(0x00, BYTE);  
 }
 
 /*
@@ -995,8 +776,6 @@ void debugprint() {
   Serial.println(logicIndex, DEC);
   Serial.print("triggerIndex = ");
   Serial.println(triggerIndex, DEC);
-  Serial.print("rleEnabled = ");
-  Serial.println(rleEnabled, DEC);
 
   Serial.println("Bytes:");
 
@@ -1006,7 +785,7 @@ void debugprint() {
     } 
     else {
       Serial.print(savebytes[i], HEX);
-      Serial.write(' ');
+      Serial.print(' ', BYTE);
     }
   }
   Serial.println("done...");
@@ -1023,11 +802,7 @@ void debugdump() {
   Serial.print("\r\n");
 
   for (i = 0 ; i < MAX_CAPTURE_SIZE; i++) {
-#ifdef SHIFTBITS
-    Serial.print(logicdata[i] >> SHIFTBITS, HEX);
-#else
     Serial.print(logicdata[i], HEX);
-#endif
     Serial.print(" ");
     if (j == 32) {
       Serial.print("\r\n");
@@ -1039,14 +814,3 @@ void debugdump() {
 #endif /* DEBUG */
 
 
-
-
-
-
-
-
-
-
-
-
-

ols.profile-agla.cfg

@@ -7,11 +7,11 @@ device.description = Arduino Generic Logic Analyzer
 # The device interface, SERIAL only
 device.interface = SERIAL
 # The device's native clockspeed, in Hertz.
-device.clockspeed = 16000000
+device.clockspeed = 100000000
 # Whether or not double-data-rate is supported by the device (also known as the "demux"-mode).
 device.supports_ddr = false
 # Supported sample rates in Hertz, separated by comma's
-device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000, 2000000, 4000000
+device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000
 # What capture clocks are supported
 device.captureclock = INTERNAL
 # The supported capture sizes, in bytes
@@ -19,7 +19,7 @@ device.capturesizes = 64, 128, 256, 512, 1024
 # Whether or not the noise filter is supported
 device.feature.noisefilter = false
 # Whether or not Run-Length encoding is supported
-device.feature.rle = true
+device.feature.rle = false
 # Whether or not a testing mode is supported
 device.feature.testmode = false
 # Whether or not triggers are supported
@@ -30,7 +30,7 @@ device.trigger.stages = 1
 device.trigger.complex = false
 
 # The total number of channels usable for capturing
-device.channel.count = 6
+device.channel.count = 5
 # The number of channels groups, together with the channel count determines the channels per group
 device.channel.groups = 1
 # Whether the capture size is limited by the enabled channel groups
@@ -39,15 +39,13 @@ device.capturesize.bound = false
 device.channel.numberingschemes = DEFAULT
 
 # Is a delay after opening the port and device detection needed? (0 = no delay, >0 = delay in milliseconds)
-device.open.portdelay = 2000
+device.open.portdelay = 500
-# The receive timeout for the device (in milliseconds, 100 = default, <=0 = no timeout)
-device.receive.timeout = 100
 # Does the device need a high or low DTR-line to operate correctly? (high = true, low = false)
 device.open.portdtr = true
 # Which metadata keys correspond to this device profile? Value is a comma-separated list of (double quoted) names...
 device.metadata.keys = "AGLAv0"
 
-# In which order are samples sent back from the device? false = last sample first, true = first sample first
+# In which order are samples sent back from the device? true = last sample first, false = first sample first
-device.samples.reverseOrder = true
+device.samples.reverseOrder = false
 
 ###EOF###

ols.profile-aglam.cfg

@@ -1,53 +0,0 @@
-# Configuration for Arduino Mega Logic Analyzer profile
-
-# The short (single word) type of the device described in this profile
-device.type = AGLAM
-# A longer description of the device
-device.description = Arduino Mega Logic Analyzer
-# The device interface, SERIAL only
-device.interface = SERIAL
-# The device's native clockspeed, in Hertz.
-device.clockspeed = 16000000
-# Whether or not double-data-rate is supported by the device (also known as the "demux"-mode).
-device.supports_ddr = false
-# Supported sample rates in Hertz, separated by comma's
-device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000, 2000000, 4000000
-# What capture clocks are supported
-device.captureclock = INTERNAL
-# The supported capture sizes, in bytes
-device.capturesizes = 64, 128, 256, 512, 1024, 2048, 4096, 7168
-# Whether or not the noise filter is supported
-device.feature.noisefilter = false
-# Whether or not Run-Length encoding is supported
-device.feature.rle = false
-# Whether or not a testing mode is supported
-device.feature.testmode = false
-# Whether or not triggers are supported
-device.feature.triggers = true
-# The number of trigger stages
-device.trigger.stages = 1
-# Whether or not "complex" triggers are supported
-device.trigger.complex = false
-
-# The total number of channels usable for capturing
-device.channel.count = 8
-# The number of channels groups, together with the channel count determines the channels per group
-device.channel.groups = 1
-# Whether the capture size is limited by the enabled channel groups
-device.capturesize.bound = false
-# Which numbering does the device support
-device.channel.numberingschemes = DEFAULT
-
-# Is a delay after opening the port and device detection needed? (0 = no delay, >0 = delay in milliseconds)
-device.open.portdelay = 2000
-# The receive timeout for the device (in milliseconds, 100 = default, <=0 = no timeout)
-device.receive.timeout = 100
-# Does the device need a high or low DTR-line to operate correctly? (high = true, low = false)
-device.open.portdtr = true
-# Which metadata keys correspond to this device profile? Value is a comma-separated list of (double quoted) names...
-device.metadata.keys = "AGLAMv0"
-
-# In which order are samples sent back from the device? false = last sample first, true = first sample first
-device.samples.reverseOrder = true
-
-###EOF###