Tweak README

Also move a couple more things under #ifdef DEBUG in an attempt to
reduce the code size for ATmega168.
It current doesn't fit in the '168 but maybe after some more tweaks.

README

@@ -1,6 +1,15 @@
 SUMP compatible logic analyzer for Arduino
 ==========================================
 
+NOTE: With v0.11 you can now sample at 4MHz & 2MHz rates in addition to the 
+      previous 1MHz and lower rates.  This is done via unrolled loops which
+      makes the source code huge and the binary takes much more of the flash.
+      v0.11 is just slightly to big for an ATmega168's flash.  You can comment
+      out either captureInline2mhz() or captureInline4mhz() and it will fit. 
+
+NOTE: v0.09 switched the channels BACK to pins 8-13 for trigger reliability.
+      Please report any issues.  Uncomment USE_PORTD for pins 2-7.
+
 This Arduino sketch implements a SUMP protocol compatible with the standard
 SUMP client as well as the alternative client from here:
 	http://www.lxtreme.nl/ols/
@@ -34,7 +43,7 @@ platform, but on the mac it is here by default:
 To use this with the original or alternative SUMP clients,
 use these settings:
 
-Sampling rate: 1MHz (or lower)
+Sampling rate: 4MHz (or lower)
 Channel Groups: 0 (zero) only
 Recording Size:
    ATmega168:  532 (or lower)
@@ -51,5 +60,5 @@ Please try it out and report back.
 This master branch now supports Arduino 1.0 only.
 Checkout branch logic_analyzer_v0_5 for Arduino 22 support.
 
-Release: v0.06 November 4, 2011.
+Release: v0.11 August 3, 2013.
 

logic_analyzer.ino

@@ -2,7 +2,7 @@
  *
  * SUMP Protocol Implementation for Arduino boards.
  *
- * Copyright (c) 2011 Andrew Gillham
+ * Copyright (c) 2011,2012,2013 Andrew Gillham
  * All rights reserved.
  *
  * Redistribution and use in source and binary forms, with or without
@@ -25,21 +25,20 @@
  * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
  * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
- *	$Id: logic_analyzer.ino,v 1.21 2012/02/27 20:19:44 gillham Exp $
  *
  */
 
 /*
+ * NOTE: v0.09 switched the channels BACK to pins 8-13 for trigger reliability.
+ *       Please report any issues.  Uncomment USE_PORTD for pins 2-7.
+ *
  * This Arduino sketch implements a SUMP protocol compatible with the standard
  * SUMP client as well as the alternative client from here:
  *	http://www.lxtreme.nl/ols/
  *
  * This SUMP protocol compatible logic analyzer for the Arduino board supports
- * 5 channels consisting of digital pins 8-12, which are the first 5 bits (0-4)
- * of PORTB. Arduino pin 13 / bit 5 is the Arduino LED, bits 6 & 7 are the
- * crystal oscillator pins.
- * Uncomment CHAN5 below if you want to use the LED pin as an input and have
- * 6 channels.
+ * 6 channels consisting of digital pins 2-7, which are the last 6 bits (2-7)
+ * of PORTD.  Bits 0 & 1 are the UART RX/TX pins.
  *
  * On the Arduino Mega board 8 channels are supported and 7k of samples.
  * Pins 22-29 (Port A) are used by default, you can change the 'CHANPIN' below
@@ -64,7 +63,7 @@
  * To use this with the original or alternative SUMP clients,
  * use these settings:
  * 
- * Sampling rate: 1MHz (or lower)
+ * Sampling rate: 4MHz (or lower)
  * Channel Groups: 0 (zero) only
  * Recording Size:
  *    ATmega168:  532 (or lower)
@@ -72,13 +71,14 @@
  *    ATmega2560: 7168 (or lower)
  * Noise Filter: doesn't matter
  * RLE: disabled (unchecked)
+ *    NOTE: Preliminary RLE support for 50Hz or less exists, please test it.
  *
  * Triggering is still a work in progress, but generally works for samples
  * below 1MHz.  1MHz works for a basic busy wait trigger that doesn't store
  * until after the trigger fires.
  * Please try it out and report back.
  *
- * Release: v0.06 November 4, 2011.
+ * Release: v0.11 August 3, 2013.
  *
  */
 
@@ -98,10 +98,14 @@ void get_metadata(void);
 void debugprint(void);
 void debugdump(void);
 
+
+/*
+ * Should we use PORTD or PORTB?  (default is PORTB)
+ * PORTD support with triggers seems to work but needs more testing.
+ */
+//#define USE_PORTD 1
+
 /*
- * Uncomment CHAN5 to use it as an additional input on a normal Arduino.
- * You'll need to change the number of channels in the device profile as well.
- *
  * Arduino device profile:      ols.profile-agla.cfg
  * Arduino Mega device profile: ols.profile-aglam.cfg
  */
@@ -116,13 +120,24 @@ void debugdump(void);
 #define CHAN6 28
 #define CHAN7 29
 #else
+#if defined(USE_PORTD)
+#define CHANPIN PIND
+#define CHAN0 2
+#define CHAN1 3
+#define CHAN2 4
+#define CHAN3 5
+#define CHAN4 6
+#define CHAN5 7
+#else
 #define CHANPIN PINB
 #define CHAN0 8
 #define CHAN1 9
 #define CHAN2 10
 #define CHAN3 11
 #define CHAN4 12
-//#define CHAN5 13
+/* Comment out CHAN5 if you don't want to use the LED pin for an input */
+#define CHAN5 13
+#endif /* USE_PORTD */
 #endif
 #define ledPin 13
 
@@ -138,10 +153,11 @@ void debugdump(void);
 #define SUMP_TRIGGER_VALUES 0xC1
 #define SUMP_TRIGGER_CONFIG 0xC2
 
-/* flags are ignored. */
+/* Most flags (except RLE) are ignored. */
 #define SUMP_SET_DIVIDER 0x80
 #define SUMP_SET_READ_DELAY_COUNT 0x81
 #define SUMP_SET_FLAGS 0x82
+#define SUMP_SET_RLE 0x0100
 
 /* extended commands -- self-test unsupported, but metadata is returned. */
 #define SUMP_SELF_TEST 0x03
@@ -162,6 +178,15 @@ void debugdump(void);
 #define CAPTURE_SIZE 532
 #endif
 
+#ifdef USE_PORTD
+#define DEBUG_ENABLE DDRB = DDRB | B00000001
+#define DEBUG_ON PORTB = B00000001
+#define DEBUG_OFF PORTB = B00000000
+#else
+#define DEBUG_ENABLE DDRD = DDRD | B10000000
+#define DEBUG_ON PORTD = B10000000
+#define DEBUG_OFF PORTD = B00000000
+#endif
 #define DEBUG
 #ifdef DEBUG
 #define MAX_CAPTURE_SIZE DEBUG_CAPTURE_SIZE
@@ -191,36 +216,61 @@ unsigned int trigger_values = 0;
 unsigned int useMicro = 0;
 unsigned int delayTime = 0;
 unsigned long divider = 0;
+boolean rleEnabled = 0;
 
 void setup()
 {
   Serial.begin(115200);
 
   /*
-   * set debug pin to output right away so it settles.
+   * set debug pin (digital pin 8) to output right away so it settles.
    * this gets toggled during sampling as a way to measure
    * the sample time.  this is used during development to
    * properly pad out the sampling routines.
    */
-  DDRD = DDRD | B10000000; /* debug measurement pin */
+  DEBUG_ENABLE; /* debug measurement pin */
 
   pinMode(CHAN0, INPUT);
   pinMode(CHAN1, INPUT);
   pinMode(CHAN2, INPUT);
   pinMode(CHAN3, INPUT);
   pinMode(CHAN4, INPUT);
-#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-  pinMode(CHAN5, INPUT);
-  pinMode(CHAN6, INPUT);
-  pinMode(CHAN7, INPUT);
-  pinMode(ledPin, OUTPUT);
-#else
 #ifdef CHAN5
   pinMode(CHAN5, INPUT);
+#endif
+#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
+  pinMode(CHAN6, INPUT);
+  pinMode(CHAN7, INPUT);
 #else
+#ifndef CHAN5
   pinMode(ledPin, OUTPUT);
-#endif /* CHAN5 */
+#endif
 #endif /* Mega */
+
+#if 0
+
+  /*
+   * This sets up timer2 at 100KHz to toggle a pin.  This is useful
+   * for debugging as it gives an internally precise signal source.
+   * This doesn't work on the Arduino Mega.  Use on the Uno or older.
+   * We're using the same clock source for the timer & our sampling.
+   */
+
+  /* Set OC2A (digital pin 11) to output so we can toggle it. */
+  pinMode(11, OUTPUT);
+
+  /* reset timer to zero */
+  TCNT2 = 0;
+  TCCR2A = 0;
+  TCCR2B = 0;
+  OCR2A = 0;
+
+  /* Set CTC mode and toggle on compare. */
+  TCCR2A = _BV (COM2A0) | _BV (WGM21);
+  /* 79 = 100KHz, 15 = 500KHz, 7 = 1MHz */
+  OCR2A = 79;
+  TCCR2B = _BV (CS20);
+#endif
 }
 
 void loop()
@@ -258,7 +308,16 @@ void loop()
        * so in that case (delayTime == 1 and triggers enabled) use
        * captureMicro() instead of triggerMicro().
        */
-      if (useMicro) {
+
+      if (divider == 24) {
+        /* 4.0MHz */
+        captureInline4mhz();
+      } 
+      else if (divider == 49) {
+        /* 2.0MHz */
+        captureInline2mhz();
+      } 
+      else if (useMicro) {
         if (trigger && (delayTime != 1)) {
           triggerMicro();
         } 
@@ -276,7 +335,11 @@ void loop()
        * we can just use it directly as our trigger mask.
        */
       getCmd();
+#ifdef USE_PORTD
+      trigger = cmdBytes[0] << 2;
+#else
       trigger = cmdBytes[0];
+#endif
       break;
     case SUMP_TRIGGER_VALUES:
       /*
@@ -284,7 +347,11 @@ void loop()
        * defines whether we're looking for it to be high or low.
        */
       getCmd();
+#ifdef USE_PORTD
+      trigger_values = cmdBytes[0] << 2;
+#else
       trigger_values = cmdBytes[0];
+#endif
       break;
     case SUMP_TRIGGER_CONFIG:
       /* read the rest of the command bytes, but ignore them. */
@@ -323,8 +390,9 @@ void loop()
         delayCount = MAX_CAPTURE_SIZE;
       break;
     case SUMP_SET_FLAGS:
-      /* read the rest of the command bytes, but ignore them. */
+      /* read the rest of the command bytes and check if RLE is enabled. */
       getCmd();
+      rleEnabled = ((cmdBytes[1] & B1000000) != 0);
       break;
     case SUMP_GET_METADATA:
       /*
@@ -357,9 +425,7 @@ void loop()
        * you can use the Arduino serial monitor and send a '1' and get
        * a debug printout.  useless except for development.
        */
-#ifndef CHAN5
       blinkled();
-#endif /* !CHAN5 */
       debugprint();
       break;
     case '2':
@@ -425,10 +491,10 @@ void getCmd() {
  */
 
 void captureMicro() {
-  int i;
+  unsigned int i;
 
   /*
-   * basic trigger, wait until all trigger conditions are met on port B.
+   * basic trigger, wait until all trigger conditions are met on port.
    * this needs further testing, but basic tests work as expected.
    */
   if (trigger) {
@@ -447,37 +513,39 @@ void captureMicro() {
    * this is used during development to measure the sample intervals.
    * it is best to just leave the toggling in place so we don't alter
    * any timing unexpectedly.
-   * Arduino pin 7 is being used here.
+   * Arduino digital pin 8 is being used here.
    */
-  DDRD = DDRD | B10000000;
-  PORTD = B10000000;
+  DEBUG_ENABLE;
+#ifdef DEBUG
+  DEBUG_ON;
   delayMicroseconds(20);
-  PORTD = B00000000;
+  DEBUG_OFF;
   delayMicroseconds(20);
-  PORTD = B10000000;
+  DEBUG_ON;
   delayMicroseconds(20);
-  PORTD = B00000000;
+  DEBUG_OFF;
   delayMicroseconds(20);
+#endif
 
   if (delayTime == 1) {
     /*
      * 1MHz sample rate = 1 uS delay so we can't use delayMicroseconds
      * since our loop takes some time.  The delay is padded out by hand.
      */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     for (i = 0 ; i < readCount; i++) {
       logicdata[i] = CHANPIN;
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
   } 
   else if (delayTime == 2) {
     /*
      * 500KHz sample rate = 2 uS delay, still pretty fast so we pad this
      * one by hand too.
      */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     for (i = 0 ; i < readCount; i++) {
       logicdata[i] = CHANPIN;
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
@@ -487,7 +555,7 @@ void captureMicro() {
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
   } 
   else {
     /*
@@ -496,13 +564,13 @@ void captureMicro() {
      * a better logic analyzer)
      * start of real measurement
      */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     for (i = 0 ; i < readCount; i++) {
       logicdata[i] = CHANPIN;
       delayMicroseconds(delayTime - 1);
       __asm__("nop\n\t""nop\n\t");
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
   }
 
   /* re-enable interrupts now that we're done sampling. */
@@ -513,7 +581,11 @@ void captureMicro() {
    * is done for any triggers, this is effectively the 0/100 buffer split.
    */
   for (i = 0 ; i < readCount; i++) {
+#ifdef USE_PORTD
+    Serial.write(logicdata[i] >> 2);
+#else
     Serial.write(logicdata[i]);
+#endif
   }
 }
 
@@ -535,21 +607,60 @@ void captureMicro() {
  * this basic functionality.
  */
 void captureMilli() {
-  int i;
+  unsigned int i = 0;
 
-  /*
-   * very basic trigger, just like in captureMicros() above.
-   */
-  if (trigger) {
-    while ((trigger_values ^ CHANPIN) & trigger);
-  }
+  if(rleEnabled) {
+    /*
+     * very basic trigger, just like in captureMicros() above.
+     */
+    if (trigger) {
+      while ((trigger_values ^ (CHANPIN & B01111111)) & trigger);
+    }
 
-  for (i = 0 ; i < readCount; i++) {
-    logicdata[i] = CHANPIN;
-    delay(delayTime);
+    byte lastSample = 0;
+    byte sampleCount = 0;
+
+    while(i < readCount) {
+      /*
+       * Implementation of the RLE unlimited protocol: timings might be off a little
+       */
+      if(lastSample == (CHANPIN & B01111111) && sampleCount < 127) {
+        sampleCount++;
+        delay(delayTime);
+        continue;
+      }
+      if(sampleCount != 0) {
+        logicdata[i] = B10000000 | sampleCount;
+        sampleCount = 0;
+        i++;
+        continue;
+      }
+      logicdata[i] = (CHANPIN & B01111111);
+      lastSample = (CHANPIN & B01111111);
+      delay(delayTime);
+
+      i++;
+    }
+  } 
+  else {
+    /*
+     * very basic trigger, just like in captureMicros() above.
+     */
+    if (trigger) {
+      while ((trigger_values ^ CHANPIN) & trigger);
+    }
+
+    for (i = 0 ; i < readCount; i++) {
+      logicdata[i] = CHANPIN;
+      delay(delayTime);
+    }
   }
   for (i = 0 ; i < readCount; i++) {
+#ifdef USE_PORTD
+    Serial.write(logicdata[i] >> 2);
+#else
     Serial.write(logicdata[i]);
+#endif
   }
 }
 
@@ -562,7 +673,7 @@ void captureMilli() {
  * 
  */
 void triggerMicro() {
-  int i = 0;
+  unsigned int i = 0;
 
   logicIndex = 0;
   triggerIndex = 0;
@@ -579,17 +690,19 @@ void triggerMicro() {
    * this is used during development to measure the sample intervals.
    * it is best to just leave the toggling in place so we don't alter
    * any timing unexpectedly.
-   * Arduino pin 7 is being used here.
+   * Arduino digital pin 8 is being used here.
    */
-  DDRD = DDRD | B10000000;
-  PORTD = B10000000;
+  DEBUG_ENABLE;
+#ifdef DEBUG
+  DEBUG_ON;
   delayMicroseconds(20);
-  PORTD = B00000000;
+  DEBUG_OFF;
   delayMicroseconds(20);
-  PORTD = B10000000;
+  DEBUG_ON;
   delayMicroseconds(20);
-  PORTD = B00000000;
+  DEBUG_OFF;
   delayMicroseconds(20);
+#endif
 
   if (delayTime == 1) {
     /*
@@ -613,9 +726,9 @@ void triggerMicro() {
      * we always start capturing at the start of the buffer
      * and use it as a circular buffer
      */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     while ((trigger_values ^ (logicdata[logicIndex] = CHANPIN)) & trigger) {
-      /* PORTD = B00000000; */
+      /* DEBUG_OFF; */
       /* increment index. */
       logicIndex++;
       if (logicIndex >= readCount) {
@@ -627,11 +740,11 @@ void triggerMicro() {
        * __asm__("nop\n\t""nop\n\t""nop\n\t");
        */
       __asm__("nop\n\t");
-      /* PORTD = B10000000; */
+      /* DEBUG_ON; */
     }
     /* this pads the immediate trigger case to 2.0 uS, just as an example. */
     __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
 
     /* 
      * One sample size delay. ends up being 2 uS combined with assignment
@@ -646,7 +759,7 @@ void triggerMicro() {
     triggerIndex = logicIndex;
 
     /* keep sampling for delayCount after trigger */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     /*
      * this is currently taking:
      * 1025.5 uS for 512 samples. (512 samples, 0/100 split)
@@ -661,7 +774,7 @@ void triggerMicro() {
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
     delayMicroseconds(100);
   } 
   else {
@@ -674,9 +787,9 @@ void triggerMicro() {
      * and use it as a circular buffer
      *
      */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     while ((trigger_values ^ (logicdata[logicIndex] = CHANPIN)) & trigger) {
-      /* PORTD = B00000000; */
+      /* DEBUG_OFF; */
       /* increment index. */
       logicIndex++;
       if (logicIndex >= readCount) {
@@ -688,9 +801,9 @@ void triggerMicro() {
       }
       delayMicroseconds(delayTime - 3);
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t""nop\n\t");
-      /* PORTD = B10000000; */
+      /* DEBUG_ON; */
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
 
     /* 'logicIndex' now points to trigger sample, keep track of it */
     triggerIndex = logicIndex;
@@ -705,7 +818,7 @@ void triggerMicro() {
     __asm__("nop\n\t""nop\n\t""nop\n\t");
 
     /* keep sampling for delayCount after trigger */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     for (i = 0 ; i < delayCount; i++) {
       if (logicIndex >= readCount) {
         logicIndex = 0;
@@ -716,7 +829,7 @@ void triggerMicro() {
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t");
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
     delayMicroseconds(100);
   }
 
@@ -737,7 +850,11 @@ void triggerMicro() {
     if (logicIndex >= readCount) {
       logicIndex = 0;
     }
+#ifdef USE_PORTD
+    Serial.write(logicdata[logicIndex++] >> 2);
+#else
     Serial.write(logicdata[logicIndex++]);
+#endif
   }
 }
 
@@ -785,6 +902,14 @@ void get_metadata() {
   Serial.write('0');
   Serial.write((uint8_t)0x00);
 
+  /* firmware version */
+  Serial.write((uint8_t)0x02);
+  Serial.write('0');
+  Serial.write('.');
+  Serial.write('1');
+  Serial.write('1');
+  Serial.write((uint8_t)0x00);
+
   /* sample memory */
   Serial.write((uint8_t)0x21);
   Serial.write((uint8_t)0x00);
@@ -803,14 +928,14 @@ void get_metadata() {
   Serial.write((uint8_t)0x14);
 #endif /* Mega */
 
-  /* sample rate (1MHz) */
+  /* sample rate (4MHz) */
   Serial.write((uint8_t)0x23);
   Serial.write((uint8_t)0x00);
-  Serial.write((uint8_t)0x0F);
-  Serial.write((uint8_t)0x42);
-  Serial.write((uint8_t)0x40);
+  Serial.write((uint8_t)0x3D);
+  Serial.write((uint8_t)0x09);
+  Serial.write((uint8_t)0x00);
 
-  /* number of probes (5 by default on Arduino, 8 on Mega) */
+  /* number of probes (6 by default on Arduino, 8 on Mega) */
   Serial.write((uint8_t)0x40);
 #if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
   Serial.write((uint8_t)0x08);
@@ -855,6 +980,8 @@ void debugprint() {
   Serial.println(logicIndex, DEC);
   Serial.print("triggerIndex = ");
   Serial.println(triggerIndex, DEC);
+  Serial.print("rleEnabled = ");
+  Serial.println(rleEnabled, DEC);
 
   Serial.println("Bytes:");
 
@@ -881,7 +1008,11 @@ void debugdump() {
   Serial.print("\r\n");
 
   for (i = 0 ; i < MAX_CAPTURE_SIZE; i++) {
+#ifdef USE_PORTD
+    Serial.print(logicdata[i] >> 2, HEX);
+#else
     Serial.print(logicdata[i], HEX);
+#endif
     Serial.print(" ");
     if (j == 32) {
       Serial.print("\r\n");
@@ -896,3 +1027,9 @@ void debugdump() {
 
 
 
+
+
+
+
+
+

ols.profile-agla.cfg

@@ -11,7 +11,7 @@ device.clockspeed = 16000000
 # Whether or not double-data-rate is supported by the device (also known as the "demux"-mode).
 device.supports_ddr = false
 # Supported sample rates in Hertz, separated by comma's
-device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000
+device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000, 2000000, 4000000
 # What capture clocks are supported
 device.captureclock = INTERNAL
 # The supported capture sizes, in bytes
@@ -19,7 +19,7 @@ device.capturesizes = 64, 128, 256, 512, 1024
 # Whether or not the noise filter is supported
 device.feature.noisefilter = false
 # Whether or not Run-Length encoding is supported
-device.feature.rle = false
+device.feature.rle = true
 # Whether or not a testing mode is supported
 device.feature.testmode = false
 # Whether or not triggers are supported
@@ -30,7 +30,7 @@ device.trigger.stages = 1
 device.trigger.complex = false
 
 # The total number of channels usable for capturing
-device.channel.count = 5
+device.channel.count = 6
 # The number of channels groups, together with the channel count determines the channels per group
 device.channel.groups = 1
 # Whether the capture size is limited by the enabled channel groups
@@ -39,7 +39,7 @@ device.capturesize.bound = false
 device.channel.numberingschemes = DEFAULT
 
 # Is a delay after opening the port and device detection needed? (0 = no delay, >0 = delay in milliseconds)
-device.open.portdelay = 1500
+device.open.portdelay = 2000
 # The receive timeout for the device (in milliseconds, 100 = default, <=0 = no timeout)
 device.receive.timeout = 100
 # Does the device need a high or low DTR-line to operate correctly? (high = true, low = false)

ols.profile-aglam.cfg

@@ -11,7 +11,7 @@ device.clockspeed = 16000000
 # Whether or not double-data-rate is supported by the device (also known as the "demux"-mode).
 device.supports_ddr = false
 # Supported sample rates in Hertz, separated by comma's
-device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000
+device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000, 2000000, 4000000
 # What capture clocks are supported
 device.captureclock = INTERNAL
 # The supported capture sizes, in bytes