this change is mainly relevant for the SIMtrace board, but also
affects the others.
First we ensure VCC_PHONE is not forwarded to VCC_SIM because the
card could affect the signal (card could draw too much current or
feed back current in).
next we disable VCC_SIM. the card slot does not need to be
powered, and the FPF2019 leaks current back to VCC_PHONE, even
with forwarding disabled (the reverse current protection only
kicks in when VCC_PHONE is briefly shorted to ground, but still
leaks 0.6V).
enable the ADC channels normally used to measure VCC, even if
not used. the dedicated ADC pins leak current when left
unconfigured. enabling them puts them in high impedance.
Change-Id: If1487c1c191838aaa08b654e49cd31c7180ffc19
the reset/ATR handling has been heavily updated/fixed.
instead of using the timer counter peripheral to handle
the waiting time and corresponding timeout, the USART peripheral
internal timeout mechanism is used.
this is particularly important for the SIMtrace board since the
clock signal is not connected to the timer counter.
thus this change adds card emulation support for SIMtrace boards.
Fi and Di have been properly rename to F and D since the "i"
stands only for an "indicated" value, not the actual value.
this does not change the USB protocol (the variable have just been
renamed).
additional variables store more information about the card
capabilities
NOTE: it has only be tested for the SIMtrace board
Change-Id: Ibcb2c8cace9137695adf5fb3de43566f7cfb93b5
since simtrace supports multiple application, but currently not
at the same time, the feature support is not app specific
Change-Id: I98ff92450cc2a247b294d2e15df171f3fe7c5156
this is the shortest and simplest ATR possible according to the
ISO 7816-3 spec.
it does not offer any non-default parameters (F, D, WI, ...)
Change-Id: I4ff41b5120bcadca652296f9d3691f7606be2bd2
the simtrace board uses a bus switch not used on qmod and owhw to
switch the SIM between physical and virtual
Change-Id: Ieaf2ed4761fc3e04f33f9aac5c04a768c9a6f71e
monitoring the state changes of the VCC and nRST lines is required
to correctly detect warm and cold reset
Change-Id: I72099956332724f84226e1495fdc5a5b1a034695
this will become part of libosmocore since it it common to smart
card related projects (such as osmo-ccid-firmware)
Change-Id: I3d4c65d137fc4555fcb256443feadd1c695de73d
else it's too nosy while debugging other components, not often
used, and break the flow since it does not and a line.
Change-Id: I8920ff7c33b4c9fb174bb31a29334a63fcbede43
the longer output is to fast and often incomplete.
the shorter version is enough to view the progress when not
debugging.
Change-Id: I97bb84da68d1f3bc14fb7c05400edf1748f55460
this just adds the name of the TPDU state on top of the state number.
the ISO state is cleaned up accordingly
Change-Id: Id5104a2c3579dedb092c179748e9ed525673841c
the EEPROM byte output was causing data loss on the serial output,
resulting is automatic tests failing.
instead an end text will be output to detect the end of the procedure.
Change-Id: Ib8d3cbd01d0e34432d424355f4fafb24bc5273a1
the error code returned by vsnprintf was ignored,
resulting in printing the string from a previous print.
Change-Id: I8506b05d56da55d1357a1234917adf341b46e1db
Wformat requires uint32_t to be used in format string with the 'l'
qualifier (l = long = at least 32 bits).
this qualifier was not handled before.
since on ARM 32-bit int == long we can simply ignore it (stdio
already does not support 64-bit data).
Change-Id: Ib506a66f68712c6b3eeb5129a39abf47ec86a2a7
the higher baud rate allows for more debugging (without dropping
data) and is well supported by USB for UART adapters (this
standard baud rate is 8 x 115200).
the closest matching integer value is calculated for UART CR.
no floating point calculation can be used since this would
increase the size of the resulting binary by ~ 2kB (for the
softfp). this is not possible for the DFU since it already is
close to the maximum size of 16 kB.
Change-Id: I82b74f697342d580ccb79ada4715f35f4e8cca86
UART baud rate is main clock (MCK) divided by CR*16.
The MCK values are chosen >= 48 MHz and <= 64 MHz to have a near
integer value CR for a baud rate of 921600 bps.
The end MCK frequency between simtrace and qmod differ slightly
but are close to 58 MHz.
Change-Id: Iaa4a97fc68494c93b9d128503515d88049de506c
This fixes a bug, identified by the below compiler warning:
libboard/owhw/source/owhw.c: In function 'cardsim_gpio_init':
libboard/owhw/source/owhw.c:39:16: warning: passing argument 1 of 'PIO_Configure' from incompatible pointer type [-Wincompatible-pointer-types]
PIO_Configure(&pins_cardsim, ARRAY_SIZE(pins_cardsim));
^
In file included from ./atmel_softpack_libraries/libchip_sam3s/chip.h:45:0,
from libboard/owhw/source/owhw.c:20:
./atmel_softpack_libraries/libchip_sam3s/include/pio.h:189:16: note: expected 'const Pin * {aka const struct _Pin *}' but argument is of type 'const Pin (*)[2] {aka const struct _Pin (*)[2]}'
extern uint8_t PIO_Configure( const Pin *list, uint32_t size ) ;
^~~~~~~~~~~~~
Change-Id: I4c1de66c0b8475bb355b1d128f6ec88b2f2a7fcf
There have been tons of format-string related bugs in our code which
we never discovered due to disabling -Wformat. Let's fix that.
Change-Id: I5ec466361bcc526fac1f4897673264ee5af3458b
repeating the EEPROM erase (byte write) in case of byte write failure
could lead in an infinite loop.
log the error an return error code instead.
Change-Id: Id6f3654d877ca772ba04237da91a6e86e3f441ec
USB reset can be signaled by pulling low USB D+ for at least 10 ms,
according to the USB specification. This force a re-enumeration.
This time is increased to 20 ms to work with more USB HUBs.
Some SAM3S based board have external D+ pull-up mechanism (such as
SIMtrace) which needs to be used to pull D+ low.
This is a legacy mechanism from SAM7S history.
This mechanism is not required anymore on the SAM3S, and the qmod
does not use it. When the USB HAL is suspended, the transceiver is
disabled, causing D+ and D- to be pulled low. Then the HAL is activated
again. This is particularly required when DFU is started (and
enumerated), and after flashing the SAM3S switched to the main
application (without reset), so it can properly re-enumerate.
This board difference is now defined on the board header.
Change-Id: I9b58d8101c2fcf5595026b675728826af26127a3
moving the define after the header fixes the following warning:
from ./atmel_softpack_libraries/libchip_sam3s/source/exceptions.c:46:
libcommon/include/stdio.h:63:12: warning: redundant redeclaration of 'printf_sync' [-Wredundant-decls]
signed int printf_sync(const char *pFormat, ...);
^~~~~~~~~~~
./atmel_softpack_libraries/libchip_sam3s/source/exceptions.c:45:16: note: previous declaration of 'printf_sync' was here
#define printf printf_sync
^~~~~~~~~~~
libcommon/include/stdio.h:51:12: note: in expansion of macro 'printf'
signed int printf(const char *pFormat, ...);
Change-Id: I21a8de325e8f8b91297dd157f2d6a0f64434bb28
osmo_hexdump is particularly useful.
previously it was only defined, but not implemented.
this cause random behaviour upon call, often resulting in
memory corruption.
Change-Id: Ifd9120fa951f41693903fb657d10826959f1599f
The default ISR (particularly the HardFault handler) print information,
but this information was not displayed on the console because the UART
IRQ is lower than some default blocking IRQ.
Allowing to set synchronous transfer corrects this.
The underlying Atmel exception library had to be modified to use the
synchronous output.
Making UART_PutChar always synchronous when called from an ISR is not
desired because we use TRACE_ macros is some ISR. The synchronous
output must be set explicitly.
Change-Id: I1b4ace5185cf2dc32684934ed12bf6a8682e9bad
this changes how ATR is handled.
the ATR is also printed when set (as important debug information).
the test is also updated to correspond to the new mechanism (
simulating the timeout before sending the ATR)
Change-Id: I69df797e2feadffa9f5f977cb71b69386cee7cd0
a lot of the procedures are done in ISRs, but the watchdog is only
reset in the main loop.
this causes frequent reset, particularly at the beginning were
states have to the initialized.
Change-Id: Iad364444fca9d18f9a8cf47d5e0840ccd7bac2ef
