mirror of
https://gitea.osmocom.org/sim-card/simtrace2.git
synced 2026-03-17 05:38:33 +03:00
90abc09cf3
this change is mainly relevant for the SIMtrace board, but also affects the others. First we ensure VCC_PHONE is not forwarded to VCC_SIM because the card could affect the signal (card could draw too much current or feed back current in). next we disable VCC_SIM. the card slot does not need to be powered, and the FPF2019 leaks current back to VCC_PHONE, even with forwarding disabled (the reverse current protection only kicks in when VCC_PHONE is briefly shorted to ground, but still leaks 0.6V). enable the ADC channels normally used to measure VCC, even if not used. the dedicated ADC pins leak current when left unconfigured. enabling them puts them in high impedance. Change-Id: If1487c1c191838aaa08b654e49cd31c7180ffc19
This is the source code for SIMtrace 2 firmwares.
= Hardware
== Micro-Controller
The firmware is for Microchip (formerly Atmel) ATSAM3S4B micro-controllers (MCU).
Product page: https://www.microchip.com/wwwproducts/en/ATSAM3S4B
Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-6500-32-bit-Cortex-M3-Microcontroller-SAM3S4-SAM3S2-SAM3S1_Datasheet.pdf
Note: The SAM3S is now not recommended for new designs.
It can be replaced by the pin-compatible SAM4S.
The MCU can be specified using the environment variable `CHIP` (set to `sam3s4` per default) for future MCU support.
== Boards
The SIMtrace 2 firmware supports multiple boards.
A board defines a given circuit board.
While compiling the firmware, set the target board using the `BOARD` environment variable (set to `qmod` per default).
The supported boards correspond to sub-folders under `libboard`.
Current boards supported are:
* `simtrace`: The good old Osmocom SIMtrace PCB with SAM3 instead of SAM7, open hardware.
* `qmod`: A sysmocom-proprietary quad mPCIe carrier board, publicly available
* `owhw`: An undisclosed sysmocom-internal board, not publicly available
= Firmware
== Library
The firmware uses the manufacturer provided Software Package (SoftPack) micro-controller library.
The original library is available at https://www.microchip.com/design-centers/32-bit/softpacks/legacy-softpacks .
Version 2.1 from 2001 is used: http://ww1.microchip.com/downloads/en/DeviceDoc/SAM3S_softpack_2.1_for_CodeSourcery_2010q1.zip
The SIMtrace 2 project uses the `libboard_sam3s-ek`, `libchip_sam3s`, and `usb` sub-libraries, saved in `atmel_softpack_libraries` (with local modifications).
Note: SoftPack is the legacy micro-controller library.
This library is now replaced by the Advanced Software Framework (ASF): https://www.microchip.com/avr-support/advanced-software-framework-(asf) .
The SAM3S ASF documentation is available at http://asf.atmel.com/docs/latest/sam3s/html/index.html .
== Applications
An application is a specific piece of software with given functionality.
While compiling the firmware, set the target application using the `APP` environment variable (set to `dfu` per default).
The supported applications correspond to sub-folder under `apps`.
Current applications supported are:
* `dfu`: The USB DFU bootloader to flash further main appliction firmwares.
* `ccid`: To use SIMtrace 2 as USB CCID smartcard reader.
* `cardem`: To provide remote SIM operation capabilities.
* `trace`: To monitor the communication between a SIM card and a phone (corresponds to the functionality provide by the first SIMtrace)
* `triple_play`: To support the three previous functionalities, using USB configurations.
== Memories
Firmwares can be run from several memory locations:
* flash: Run natively from start of flash memory
* dfu: Run after a DFU bootloader from an offset after the first 16k of flash (the first 16k are reserved for the bootloader)
* ram: Run from within the RAM of the chip, downloaded via JTAG/SWD
== Building
A given firmware build is made for a specific combination of an application `APP` running in a certain memory `MEM` on a given board `BOARD`.
When building using `make`, set the target application using the `APP` environment variable and target board using the `BOARD` environment variable, e.g.:
* make APP=cardem BOARD=qmod
* make APP=dfu BOARD=qmod
The Makefile will create output files in the format: `bin/$(BOARD)-$(APP)-$(MEM).{elf,bin}`
The level of debug messages can be altered at compile time:
```
$ make TRACE_LEVEL=4
```
Accepted values: 0 (NO_TRACE) to 5 (DEBUG)
= Flashing
To flash a firmware image follow the instructions provided in the [wiki](https://projects.osmocom.org/projects/simtrace2/wiki/).