Improve Leonardo support.

Shift port by 1 bit on the Leonardo since PB0 is the RXLED and not
available for use via a pin.
Use a more generic method of shifting the bits since the Leonardo needs
1 bit shift and the Mega needs 2.

README

@@ -5,39 +5,27 @@ This Arduino sketch implements a SUMP protocol compatible with the standard
 SUMP client as well as the alternative client from here:
 	http://www.lxtreme.nl/ols/
 
+The alternative client version is highly recommended.  Download version
+"ols-0.9.7" or newer for built-in device profiles.
+
 This SUMP protocol compatible logic analyzer for the Arduino board supports
 5 channels consisting of digital pins 8-12, which are the first 5 bits (0-4)
 of PORTB. Arduino pin 13 / bit 5 is the Arduino LED, bits 6 & 7 are the
 crystal oscillator pins.
+
 Uncomment CHAN5 below if you want to use the LED pin as an input and have
 6 channels.
 
 On the Arduino Mega board 8 channels are supported and 7k of samples.
-Pins 22-29 (Port A) are used by default, you can change the 'CHANPIN' below
-if something else works better for you.
-
-NOTE:
-If you are using the original SUMP client, or using the alternative client
-without the device profiles, then you will get a "device not found" error.
-You must DISABLE the Arduino auto reset feature to use this logic analyzer
-code. There are various methods to do this, some boards have a jumper,
-others require you to cut a trace.  You may also install a *precisely*
-120 Ohm resistor between the reset & 5V piins.  Make sure it is really
-120 Ohm or you may damage your board.  It is much easier to use the
-alternative SUMP client referenced above.
-
-The device profiles should be included with this code.  Copy them to the
-'plugins' directory of the client.  The location varies depending on the
-platform, but on the mac it is here by default:
-/Applications/LogicSniffer.app/Contents/Resources/Java/plugins
+Pins 22-29 (Port A) are used by default.
 
 To use this with the original or alternative SUMP clients,
 use these settings:
 
-Sampling rate: 1MHz (or lower)
+Sampling rate: 4MHz (or lower) (no 2MHz on ATmega168)
 Channel Groups: 0 (zero) only
 Recording Size:
-   ATmega186:  532 (or lower)
+   ATmega168:  532 (or lower)
    ATmega328:  1024 (or lower)
    ATmega2560: 7168 (or lower)
 Noise Filter: doesn't matter
@@ -48,5 +36,38 @@ below 1MHz.  1MHz works for a basic busy wait trigger that doesn't store
 until after the trigger fires.
 Please try it out and report back.
 
-Release: v0.05 November 4, 2011.
+Older Notes
+===========================================================================
+NOTE: With v0.11 you can now sample at 4MHz & 2MHz rates in addition to the 
+      previous 1MHz and lower rates.  This is done via unrolled loops which
+      makes the source code huge and the binary takes much more of the flash.
+      v0.11 is just slightly to big for an ATmega168's flash.  You can comment
+      out either captureInline2mhz() or captureInline4mhz() and it will fit.
+      [ The code automatically skips the 2MHz code now, this isn't needed. ]
+
+NOTE: v0.09 switched the channels BACK to pins 8-13 for trigger reliability.
+      Please report any issues.  Uncomment USE_PORTD for pins 2-7.
+
+NOTE: The device profiles should be included with this code.  Copy them to the
+      'plugins' directory of the client.  The location varies depending on the
+      platform, but on the mac it is here by default:
+      /Applications/LogicSniffer.app/Contents/Resources/Java/plugins
+      [ These are included in ols-0.9.7 or newer so do not copy them. ]
+
+NOTE: If you are using the original SUMP client, then you will get a
+      "device not found" error.
+      You must DISABLE the Arduino auto reset feature to use this logic analyzer
+      code. There are various methods to do this, some boards have a jumper,
+      others require you to cut a trace.  You may also install a *precisely*
+      120 Ohm resistor between the reset & 5V piins.  Make sure it is really
+      120 Ohm or you may damage your board.  It is much easier to use the
+      alternative SUMP client referenced above.
+      [ This is not needed with ols-0.9.7 or newer. ]
+      [ DO NOT use this resistor unless absolutely necessary on old clients. ]
+
+NOTE: This master branch now supports Arduino 1.0 only.
+      Checkout branch logic_analyzer_v0_5 for Arduino 22 support.
+
+
+Release: v0.12 September 6, 2013.
 

logic_analyzer.ino

@@ -2,7 +2,7 @@
  *
  * SUMP Protocol Implementation for Arduino boards.
  *
- * Copyright (c) 2011 Andrew Gillham
+ * Copyright (c) 2011,2012,2013,2014 Andrew Gillham
  * All rights reserved.
  *
  * Redistribution and use in source and binary forms, with or without
@@ -25,46 +25,29 @@
  * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
  * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
- *	$Id: logic_analyzer.pde,v 1.17 2011-08-04 02:31:01 gillham Exp $
  *
  */
 
 /*
+ * NOTE: v0.09 switched the channels BACK to pins 8-13 for trigger reliability.
+ *       Please report any issues.  Uncomment USE_PORTD for pins 2-7.
+ *
  * This Arduino sketch implements a SUMP protocol compatible with the standard
  * SUMP client as well as the alternative client from here:
  *	http://www.lxtreme.nl/ols/
  *
  * This SUMP protocol compatible logic analyzer for the Arduino board supports
- * 5 channels consisting of digital pins 8-12, which are the first 5 bits (0-4)
- * of PORTB. Arduino pin 13 / bit 5 is the Arduino LED, bits 6 & 7 are the
- * crystal oscillator pins.
- * Uncomment CHAN5 below if you want to use the LED pin as an input and have
- * 6 channels.
+ * 6 channels consisting of digital pins 2-7, which are the last 6 bits (2-7)
+ * of PORTD.  Bits 0 & 1 are the UART RX/TX pins.
  *
  * On the Arduino Mega board 8 channels are supported and 7k of samples.
  * Pins 22-29 (Port A) are used by default, you can change the 'CHANPIN' below
  * if something else works better for you.
  *
- * NOTE:
- * If you are using the original SUMP client, or using the alternative client
- * without the device profiles, then you will get a "device not found" error.
- * You must DISABLE the Arduino auto reset feature to use this logic analyzer
- * code. There are various methods to do this, some boards have a jumper,
- * others require you to cut a trace.  You may also install a *precisely*
- * 120 Ohm resistor between the reset & 5V piins.  Make sure it is really
- * 120 Ohm or you may damage your board.
- * It is much easier to use the alternative SUMP client from here:
- *      http://www.lxtreme.nl/ols/
- *
- * The device profiles should be included with this code.  Copy them to the
- * 'plugins' directory of the client.  The location varies depending on the
- * platform, but on the mac it is here by default:
- * /Applications/LogicSniffer.app/Contents/Resources/Java/plugins
- *
  * To use this with the original or alternative SUMP clients,
  * use these settings:
  * 
- * Sampling rate: 1MHz (or lower)
+ * Sampling rate: 4MHz (or lower) (no 2MHz on ATmega168)
  * Channel Groups: 0 (zero) only
  * Recording Size:
  *    ATmega168:  532 (or lower)
@@ -72,13 +55,14 @@
  *    ATmega2560: 7168 (or lower)
  * Noise Filter: doesn't matter
  * RLE: disabled (unchecked)
+ *    NOTE: Preliminary RLE support for 50Hz or less exists, please test it.
  *
  * Triggering is still a work in progress, but generally works for samples
  * below 1MHz.  1MHz works for a basic busy wait trigger that doesn't store
  * until after the trigger fires.
  * Please try it out and report back.
  *
- * Release: v0.05 November 4, 2011.
+ * Release: v0.12 September 6, 2013.
  *
  */
 
@@ -98,10 +82,19 @@ void get_metadata(void);
 void debugprint(void);
 void debugdump(void);
 
+
+/*
+ * Should we use PORTD or PORTB?  (default is PORTB)
+ * PORTD support with triggers seems to work but needs more testing.
+ */
+//#define USE_PORTD 1
+#if defined(USE_PORTD)
+#define SHIFTBITS 2
+#elif defined(__AVR_ATmega32U4__)
+#define SHIFTBITS 1
+#endif
+
 /*
- * Uncomment CHAN5 to use it as an additional input on a normal Arduino.
- * You'll need to change the number of channels in the device profile as well.
- *
  * Arduino device profile:      ols.profile-agla.cfg
  * Arduino Mega device profile: ols.profile-aglam.cfg
  */
@@ -116,14 +109,35 @@ void debugdump(void);
 #define CHAN6 28
 #define CHAN7 29
 #else
+#if defined(USE_PORTD)
+#define CHANPIN PIND
+#define CHAN0 2
+#define CHAN1 3
+#define CHAN2 4
+#define CHAN3 5
+#define CHAN4 6
+#define CHAN5 7
+#else
 #define CHANPIN PINB
+#if defined(__AVR_ATmega32U4__)
+#define CHAN0 SCK
+#define CHAN1 MOSI
+#define CHAN2 MISO
+#define CHAN3 8
+#define CHAN4 9
+#define CHAN5 10
+#define CHAN6 11
+#else
 #define CHAN0 8
 #define CHAN1 9
 #define CHAN2 10
 #define CHAN3 11
 #define CHAN4 12
-//#define CHAN5 13
-#endif
+/* Comment out CHAN5 if you don't want to use the LED pin for an input */
+#define CHAN5 13
+#endif /* AVR_ATmega32U4 */
+#endif /* USE_PORTD */
+#endif /* Mega1280 or Mega2560 */
 #define ledPin 13
 
 /* XON/XOFF are not supported. */
@@ -138,10 +152,11 @@ void debugdump(void);
 #define SUMP_TRIGGER_VALUES 0xC1
 #define SUMP_TRIGGER_CONFIG 0xC2
 
-/* flags are ignored. */
+/* Most flags (except RLE) are ignored. */
 #define SUMP_SET_DIVIDER 0x80
 #define SUMP_SET_READ_DELAY_COUNT 0x81
 #define SUMP_SET_FLAGS 0x82
+#define SUMP_SET_RLE 0x0100
 
 /* extended commands -- self-test unsupported, but metadata is returned. */
 #define SUMP_SELF_TEST 0x03
@@ -152,16 +167,28 @@ void debugdump(void);
  * ATmega2560: 7168 (or lower)
  */
 #if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-  #define DEBUG_CAPTURE_SIZE 7168
-  #define CAPTURE_SIZE 7168
-#elif defined(__AVR_ATmega328__)
-  #define DEBUG_CAPTURE_SIZE 1024
-  #define CAPTURE_SIZE 1024
+#define DEBUG_CAPTURE_SIZE 7168
+#define CAPTURE_SIZE 7168
+#elif defined(__AVR_ATmega32U4__)
+#define DEBUG_CAPTURE_SIZE 1536
+#define CAPTURE_SIZE 1536
+#elif defined(__AVR_ATmega328P__)
+#define DEBUG_CAPTURE_SIZE 1024
+#define CAPTURE_SIZE 1024
 #else
-  #define DEBUG_CAPTURE_SIZE 532
-  #define CAPTURE_SIZE 532
+#define DEBUG_CAPTURE_SIZE 532
+#define CAPTURE_SIZE 532
 #endif
 
+#ifdef USE_PORTD
+#define DEBUG_ENABLE DDRB = DDRB | B00000001
+#define DEBUG_ON PORTB = B00000001
+#define DEBUG_OFF PORTB = B00000000
+#else
+#define DEBUG_ENABLE DDRD = DDRD | B10000000
+#define DEBUG_ON PORTD = B10000000
+#define DEBUG_OFF PORTD = B00000000
+#endif
 #define DEBUG
 #ifdef DEBUG
 #define MAX_CAPTURE_SIZE DEBUG_CAPTURE_SIZE
@@ -191,36 +218,66 @@ unsigned int trigger_values = 0;
 unsigned int useMicro = 0;
 unsigned int delayTime = 0;
 unsigned long divider = 0;
+boolean rleEnabled = 0;
 
 void setup()
 {
   Serial.begin(115200);
+  while (!Serial) {
+    ; // wait for serial port to connect. Needed for Leonardo only
+  }
+
 
   /*
-   * set debug pin to output right away so it settles.
+   * set debug pin (digital pin 8) to output right away so it settles.
    * this gets toggled during sampling as a way to measure
    * the sample time.  this is used during development to
    * properly pad out the sampling routines.
    */
-  DDRD = DDRD | B10000000; /* debug measurement pin */
+  DEBUG_ENABLE; /* debug measurement pin */
 
   pinMode(CHAN0, INPUT);
   pinMode(CHAN1, INPUT);
   pinMode(CHAN2, INPUT);
   pinMode(CHAN3, INPUT);
   pinMode(CHAN4, INPUT);
-#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-  pinMode(CHAN5, INPUT);
-  pinMode(CHAN6, INPUT);
-  pinMode(CHAN7, INPUT);
-  pinMode(ledPin, OUTPUT);
-#else
 #ifdef CHAN5
   pinMode(CHAN5, INPUT);
-#else
+#endif
+#ifdef CHAN6
+  pinMode(CHAN6, INPUT);
+#endif
+#ifdef CHAN7
+  pinMode(CHAN7, INPUT);
+#endif
+#ifndef CHAN5
   pinMode(ledPin, OUTPUT);
-#endif /* CHAN5 */
-#endif /* Mega */
+#endif
+
+#if 0
+
+  /*
+   * This sets up timer2 at 100KHz to toggle a pin.  This is useful
+   * for debugging as it gives an internally precise signal source.
+   * This doesn't work on the Arduino Mega.  Use on the Uno or older.
+   * We're using the same clock source for the timer & our sampling.
+   */
+
+  /* Set OC2A (digital pin 11) to output so we can toggle it. */
+  pinMode(11, OUTPUT);
+
+  /* reset timer to zero */
+  TCNT2 = 0;
+  TCCR2A = 0;
+  TCCR2B = 0;
+  OCR2A = 0;
+
+  /* Set CTC mode and toggle on compare. */
+  TCCR2A = _BV (COM2A0) | _BV (WGM21);
+  /* 79 = 100KHz, 15 = 500KHz, 7 = 1MHz */
+  OCR2A = 79;
+  TCCR2B = _BV (CS20);
+#endif
 }
 
 void loop()
@@ -239,10 +296,10 @@ void loop()
       break;
     case SUMP_QUERY:
       /* return the expected bytes. */
-      Serial.print('1', BYTE);
-      Serial.print('A', BYTE);
-      Serial.print('L', BYTE);
-      Serial.print('S', BYTE);
+      Serial.write('1');
+      Serial.write('A');
+      Serial.write('L');
+      Serial.write('S');
       break;
     case SUMP_ARM:
       /*
@@ -258,7 +315,18 @@ void loop()
        * so in that case (delayTime == 1 and triggers enabled) use
        * captureMicro() instead of triggerMicro().
        */
-      if (useMicro) {
+
+      if (divider == 24) {
+        /* 4.0MHz */
+        captureInline4mhz();
+      } 
+      else if (divider == 49) {
+        /* 2.0MHz */
+#if defined(__AVR_ATmega168P__)
+        captureInline2mhz();
+#endif
+      } 
+      else if (useMicro) {
         if (trigger && (delayTime != 1)) {
           triggerMicro();
         } 
@@ -276,7 +344,11 @@ void loop()
        * we can just use it directly as our trigger mask.
        */
       getCmd();
+#ifdef SHIFTBITS
+      trigger = cmdBytes[0] << SHIFTBITS;
+#else
       trigger = cmdBytes[0];
+#endif
       break;
     case SUMP_TRIGGER_VALUES:
       /*
@@ -284,7 +356,11 @@ void loop()
        * defines whether we're looking for it to be high or low.
        */
       getCmd();
+#ifdef SHIFTBITS
+      trigger_values = cmdBytes[0] << SHIFTBITS;
+#else
       trigger_values = cmdBytes[0];
+#endif
       break;
     case SUMP_TRIGGER_CONFIG:
       /* read the rest of the command bytes, but ignore them. */
@@ -323,8 +399,9 @@ void loop()
         delayCount = MAX_CAPTURE_SIZE;
       break;
     case SUMP_SET_FLAGS:
-      /* read the rest of the command bytes, but ignore them. */
+      /* read the rest of the command bytes and check if RLE is enabled. */
       getCmd();
+      rleEnabled = ((cmdBytes[1] & B1000000) != 0);
       break;
     case SUMP_GET_METADATA:
       /*
@@ -357,9 +434,7 @@ void loop()
        * you can use the Arduino serial monitor and send a '1' and get
        * a debug printout.  useless except for development.
        */
-#ifndef CHAN5
       blinkled();
-#endif /* !CHAN5 */
       debugprint();
       break;
     case '2':
@@ -425,10 +500,10 @@ void getCmd() {
  */
 
 void captureMicro() {
-  int i;
+  unsigned int i;
 
   /*
-   * basic trigger, wait until all trigger conditions are met on port B.
+   * basic trigger, wait until all trigger conditions are met on port.
    * this needs further testing, but basic tests work as expected.
    */
   if (trigger) {
@@ -447,37 +522,39 @@ void captureMicro() {
    * this is used during development to measure the sample intervals.
    * it is best to just leave the toggling in place so we don't alter
    * any timing unexpectedly.
-   * Arduino pin 7 is being used here.
+   * Arduino digital pin 8 is being used here.
    */
-  DDRD = DDRD | B10000000;
-  PORTD = B10000000;
+  DEBUG_ENABLE;
+#ifdef DEBUG
+  DEBUG_ON;
   delayMicroseconds(20);
-  PORTD = B00000000;
+  DEBUG_OFF;
   delayMicroseconds(20);
-  PORTD = B10000000;
+  DEBUG_ON;
   delayMicroseconds(20);
-  PORTD = B00000000;
+  DEBUG_OFF;
   delayMicroseconds(20);
+#endif
 
   if (delayTime == 1) {
     /*
      * 1MHz sample rate = 1 uS delay so we can't use delayMicroseconds
      * since our loop takes some time.  The delay is padded out by hand.
      */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     for (i = 0 ; i < readCount; i++) {
       logicdata[i] = CHANPIN;
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
   } 
   else if (delayTime == 2) {
     /*
      * 500KHz sample rate = 2 uS delay, still pretty fast so we pad this
      * one by hand too.
      */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     for (i = 0 ; i < readCount; i++) {
       logicdata[i] = CHANPIN;
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
@@ -487,7 +564,7 @@ void captureMicro() {
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
   } 
   else {
     /*
@@ -496,13 +573,13 @@ void captureMicro() {
      * a better logic analyzer)
      * start of real measurement
      */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     for (i = 0 ; i < readCount; i++) {
       logicdata[i] = CHANPIN;
       delayMicroseconds(delayTime - 1);
       __asm__("nop\n\t""nop\n\t");
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
   }
 
   /* re-enable interrupts now that we're done sampling. */
@@ -513,7 +590,11 @@ void captureMicro() {
    * is done for any triggers, this is effectively the 0/100 buffer split.
    */
   for (i = 0 ; i < readCount; i++) {
-    Serial.print(logicdata[i], BYTE);
+#ifdef SHIFTBITS
+    Serial.write(logicdata[i] >> SHIFTBITS);
+#else
+    Serial.write(logicdata[i]);
+#endif
   }
 }
 
@@ -535,21 +616,60 @@ void captureMicro() {
  * this basic functionality.
  */
 void captureMilli() {
-  int i;
+  unsigned int i = 0;
 
-  /*
-   * very basic trigger, just like in captureMicros() above.
-   */
-  if (trigger) {
-    while ((trigger_values ^ CHANPIN) & trigger);
-  }
+  if(rleEnabled) {
+    /*
+     * very basic trigger, just like in captureMicros() above.
+     */
+    if (trigger) {
+      while ((trigger_values ^ (CHANPIN & B01111111)) & trigger);
+    }
 
-  for (i = 0 ; i < readCount; i++) {
-    logicdata[i] = CHANPIN;
-    delay(delayTime);
+    byte lastSample = 0;
+    byte sampleCount = 0;
+
+    while(i < readCount) {
+      /*
+       * Implementation of the RLE unlimited protocol: timings might be off a little
+       */
+      if(lastSample == (CHANPIN & B01111111) && sampleCount < 127) {
+        sampleCount++;
+        delay(delayTime);
+        continue;
+      }
+      if(sampleCount != 0) {
+        logicdata[i] = B10000000 | sampleCount;
+        sampleCount = 0;
+        i++;
+        continue;
+      }
+      logicdata[i] = (CHANPIN & B01111111);
+      lastSample = (CHANPIN & B01111111);
+      delay(delayTime);
+
+      i++;
+    }
+  } 
+  else {
+    /*
+     * very basic trigger, just like in captureMicros() above.
+     */
+    if (trigger) {
+      while ((trigger_values ^ CHANPIN) & trigger);
+    }
+
+    for (i = 0 ; i < readCount; i++) {
+      logicdata[i] = CHANPIN;
+      delay(delayTime);
+    }
   }
   for (i = 0 ; i < readCount; i++) {
-    Serial.print(logicdata[i], BYTE);
+#ifdef SHIFTBITS
+    Serial.write(logicdata[i] >> SHIFTBITS);
+#else
+    Serial.write(logicdata[i]);
+#endif
   }
 }
 
@@ -562,7 +682,7 @@ void captureMilli() {
  * 
  */
 void triggerMicro() {
-  int i = 0;
+  unsigned int i = 0;
 
   logicIndex = 0;
   triggerIndex = 0;
@@ -579,17 +699,19 @@ void triggerMicro() {
    * this is used during development to measure the sample intervals.
    * it is best to just leave the toggling in place so we don't alter
    * any timing unexpectedly.
-   * Arduino pin 7 is being used here.
+   * Arduino digital pin 8 is being used here.
    */
-  DDRD = DDRD | B10000000;
-  PORTD = B10000000;
+  DEBUG_ENABLE;
+#ifdef DEBUG
+  DEBUG_ON;
   delayMicroseconds(20);
-  PORTD = B00000000;
+  DEBUG_OFF;
   delayMicroseconds(20);
-  PORTD = B10000000;
+  DEBUG_ON;
   delayMicroseconds(20);
-  PORTD = B00000000;
+  DEBUG_OFF;
   delayMicroseconds(20);
+#endif
 
   if (delayTime == 1) {
     /*
@@ -613,9 +735,9 @@ void triggerMicro() {
      * we always start capturing at the start of the buffer
      * and use it as a circular buffer
      */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     while ((trigger_values ^ (logicdata[logicIndex] = CHANPIN)) & trigger) {
-      /* PORTD = B00000000; */
+      /* DEBUG_OFF; */
       /* increment index. */
       logicIndex++;
       if (logicIndex >= readCount) {
@@ -627,11 +749,11 @@ void triggerMicro() {
        * __asm__("nop\n\t""nop\n\t""nop\n\t");
        */
       __asm__("nop\n\t");
-      /* PORTD = B10000000; */
+      /* DEBUG_ON; */
     }
     /* this pads the immediate trigger case to 2.0 uS, just as an example. */
     __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
 
     /* 
      * One sample size delay. ends up being 2 uS combined with assignment
@@ -646,7 +768,7 @@ void triggerMicro() {
     triggerIndex = logicIndex;
 
     /* keep sampling for delayCount after trigger */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     /*
      * this is currently taking:
      * 1025.5 uS for 512 samples. (512 samples, 0/100 split)
@@ -661,7 +783,7 @@ void triggerMicro() {
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
     delayMicroseconds(100);
   } 
   else {
@@ -674,17 +796,23 @@ void triggerMicro() {
      * and use it as a circular buffer
      *
      */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     while ((trigger_values ^ (logicdata[logicIndex] = CHANPIN)) & trigger) {
-      /* PORTD = B00000000; */
+      /* DEBUG_OFF; */
       /* increment index. */
       logicIndex++;
       if (logicIndex >= readCount) {
         logicIndex = 0;
       }
-      /* PORTD = B10000000; */
+      else {
+        /* pad the same number of cycles as the above assignment (needs verification) */
+        __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
+      }
+      delayMicroseconds(delayTime - 3);
+      __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t""nop\n\t");
+      /* DEBUG_ON; */
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
 
     /* 'logicIndex' now points to trigger sample, keep track of it */
     triggerIndex = logicIndex;
@@ -693,10 +821,13 @@ void triggerMicro() {
      * This needs adjustment so that we have the right spacing between the
      * before trigger samples and the after trigger samples.
      */
-    delayMicroseconds(delayTime);
+    delayMicroseconds(delayTime - 2);
+    __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
+    __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
+    __asm__("nop\n\t""nop\n\t""nop\n\t");
 
     /* keep sampling for delayCount after trigger */
-    PORTD = B10000000; /* debug timing measurement */
+    DEBUG_ON; /* debug timing measurement */
     for (i = 0 ; i < delayCount; i++) {
       if (logicIndex >= readCount) {
         logicIndex = 0;
@@ -707,7 +838,7 @@ void triggerMicro() {
       __asm__("nop\n\t""nop\n\t""nop\n\t""nop\n\t");
       __asm__("nop\n\t""nop\n\t""nop\n\t");
     }
-    PORTD = B00000000; /* debug timing measurement */
+    DEBUG_OFF; /* debug timing measurement */
     delayMicroseconds(100);
   }
 
@@ -728,7 +859,11 @@ void triggerMicro() {
     if (logicIndex >= readCount) {
       logicIndex = 0;
     }
-    Serial.print(logicdata[logicIndex++], BYTE);
+#ifdef SHIFTBITS
+    Serial.write(logicdata[logicIndex++] >> SHIFTBITS);
+#else
+    Serial.write(logicdata[logicIndex++]);
+#endif
   }
 }
 
@@ -764,61 +899,75 @@ void setupDelay() {
  */
 void get_metadata() {
   /* device name */
-  Serial.print(0x01, BYTE);
-  Serial.print('A', BYTE);
-  Serial.print('G', BYTE);
-  Serial.print('L', BYTE);
-  Serial.print('A', BYTE);
+  Serial.write((uint8_t)0x01);
+  Serial.write('A');
+  Serial.write('G');
+  Serial.write('L');
+  Serial.write('A');
 #if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-  Serial.print('M', BYTE);
+  Serial.write('M');
+#elif defined(__AVR_ATmega32U4__)
+  Serial.write('L');
 #endif /* Mega */
-  Serial.print('v', BYTE);
-  Serial.print('0', BYTE);
-  Serial.print(0x00, BYTE);
+  Serial.write('v');
+  Serial.write('0');
+  Serial.write((uint8_t)0x00);
+
+  /* firmware version */
+  Serial.write((uint8_t)0x02);
+  Serial.write('0');
+  Serial.write('.');
+  Serial.write('1');
+  Serial.write('2');
+  Serial.write((uint8_t)0x00);
 
   /* sample memory */
-  Serial.print(0x21, BYTE);
-  Serial.print(0x00, BYTE);
-  Serial.print(0x00, BYTE);
+  Serial.write((uint8_t)0x21);
+  Serial.write((uint8_t)0x00);
+  Serial.write((uint8_t)0x00);
 #if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
   /* 7168 bytes */
-  Serial.print(0x1C, BYTE);
-  Serial.print(0x00, BYTE);
-#elif defined(__AVR_ATmega328__)
+  Serial.write((uint8_t)0x1C);
+  Serial.write((uint8_t)0x00);
+#elif defined(__AVR_ATmega32U4__)
   /* 1024 bytes */
-  Serial.print(0x04, BYTE);
-  Serial.print(0x00, BYTE);
+  Serial.write((uint8_t)0x04);
+  Serial.write((uint8_t)0x00);
+#elif defined(__AVR_ATmega328P__)
+  /* 1024 bytes */
+  Serial.write((uint8_t)0x04);
+  Serial.write((uint8_t)0x00);
 #else
   /* 532 bytes */
-  Serial.print(0x02, BYTE);
-  Serial.print(0x14, BYTE);
+  Serial.write((uint8_t)0x02);
+  Serial.write((uint8_t)0x14);
 #endif /* Mega */
 
-  /* sample rate (1MHz) */
-  Serial.print(0x23, BYTE);
-  Serial.print(0x00, BYTE);
-  Serial.print(0x0F, BYTE);
-  Serial.print(0x42, BYTE);
-  Serial.print(0x40, BYTE);
+  /* sample rate (4MHz) */
+  Serial.write((uint8_t)0x23);
+  Serial.write((uint8_t)0x00);
+  Serial.write((uint8_t)0x3D);
+  Serial.write((uint8_t)0x09);
+  Serial.write((uint8_t)0x00);
 
-  /* number of probes (5 by default on Arduino, 8 on Mega) */
-  Serial.print(0x40, BYTE);
-#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
-  Serial.print(0x08, BYTE);
+  /* number of probes (6 by default on Arduino, 8 on Mega) */
+  Serial.write((uint8_t)0x40);
+#ifdef CHAN7
+  Serial.write((uint8_t)0x08);
+#elif CHAN6
+  Serial.write((uint8_t)0x07);
+#elif CHAN5
+  Serial.write((uint8_t)0x06);
 #else
-#ifdef CHAN5
-  Serial.print(0x06, BYTE);
-#else
-  Serial.print(0x05, BYTE);
-#endif /* CHAN5 */
-#endif /* Mega */
+  Serial.write((uint8_t)0x05);
+#endif
 
   /* protocol version (2) */
-  Serial.print(0x41, BYTE);
-  Serial.print(0x02, BYTE);
+  Serial.write((uint8_t)0x41);
+  Serial.write((uint8_t)0x02);
 
   /* end of data */
-  Serial.print(0x00, BYTE);  
+  Serial.write((uint8_t)0x00);  
 }
 
 /*
@@ -846,6 +995,8 @@ void debugprint() {
   Serial.println(logicIndex, DEC);
   Serial.print("triggerIndex = ");
   Serial.println(triggerIndex, DEC);
+  Serial.print("rleEnabled = ");
+  Serial.println(rleEnabled, DEC);
 
   Serial.println("Bytes:");
 
@@ -855,7 +1006,7 @@ void debugprint() {
     } 
     else {
       Serial.print(savebytes[i], HEX);
-      Serial.print(' ', BYTE);
+      Serial.write(' ');
     }
   }
   Serial.println("done...");
@@ -872,7 +1023,11 @@ void debugdump() {
   Serial.print("\r\n");
 
   for (i = 0 ; i < MAX_CAPTURE_SIZE; i++) {
+#ifdef SHIFTBITS
+    Serial.print(logicdata[i] >> SHIFTBITS, HEX);
+#else
     Serial.print(logicdata[i], HEX);
+#endif
     Serial.print(" ");
     if (j == 32) {
       Serial.print("\r\n");
@@ -884,3 +1039,14 @@ void debugdump() {
 #endif /* DEBUG */
 
 
+
+
+
+
+
+
+
+
+
+
+

ols.profile-agla.cfg

@@ -7,11 +7,11 @@ device.description = Arduino Generic Logic Analyzer
 # The device interface, SERIAL only
 device.interface = SERIAL
 # The device's native clockspeed, in Hertz.
-device.clockspeed = 100000000
+device.clockspeed = 16000000
 # Whether or not double-data-rate is supported by the device (also known as the "demux"-mode).
 device.supports_ddr = false
 # Supported sample rates in Hertz, separated by comma's
-device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000
+device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000, 2000000, 4000000
 # What capture clocks are supported
 device.captureclock = INTERNAL
 # The supported capture sizes, in bytes
@@ -19,7 +19,7 @@ device.capturesizes = 64, 128, 256, 512, 1024
 # Whether or not the noise filter is supported
 device.feature.noisefilter = false
 # Whether or not Run-Length encoding is supported
-device.feature.rle = false
+device.feature.rle = true
 # Whether or not a testing mode is supported
 device.feature.testmode = false
 # Whether or not triggers are supported
@@ -30,7 +30,7 @@ device.trigger.stages = 1
 device.trigger.complex = false
 
 # The total number of channels usable for capturing
-device.channel.count = 5
+device.channel.count = 6
 # The number of channels groups, together with the channel count determines the channels per group
 device.channel.groups = 1
 # Whether the capture size is limited by the enabled channel groups
@@ -39,13 +39,15 @@ device.capturesize.bound = false
 device.channel.numberingschemes = DEFAULT
 
 # Is a delay after opening the port and device detection needed? (0 = no delay, >0 = delay in milliseconds)
-device.open.portdelay = 500
+device.open.portdelay = 2000
+# The receive timeout for the device (in milliseconds, 100 = default, <=0 = no timeout)
+device.receive.timeout = 100
 # Does the device need a high or low DTR-line to operate correctly? (high = true, low = false)
 device.open.portdtr = true
 # Which metadata keys correspond to this device profile? Value is a comma-separated list of (double quoted) names...
 device.metadata.keys = "AGLAv0"
 
-# In which order are samples sent back from the device? true = last sample first, false = first sample first
-device.samples.reverseOrder = false
+# In which order are samples sent back from the device? false = last sample first, true = first sample first
+device.samples.reverseOrder = true
 
 ###EOF###

ols.profile-aglam.cfg

@@ -7,11 +7,11 @@ device.description = Arduino Mega Logic Analyzer
 # The device interface, SERIAL only
 device.interface = SERIAL
 # The device's native clockspeed, in Hertz.
-device.clockspeed = 100000000
+device.clockspeed = 16000000
 # Whether or not double-data-rate is supported by the device (also known as the "demux"-mode).
 device.supports_ddr = false
 # Supported sample rates in Hertz, separated by comma's
-device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000
+device.samplerates = 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000, 100000, 200000, 500000, 1000000, 2000000, 4000000
 # What capture clocks are supported
 device.captureclock = INTERNAL
 # The supported capture sizes, in bytes
@@ -39,13 +39,15 @@ device.capturesize.bound = false
 device.channel.numberingschemes = DEFAULT
 
 # Is a delay after opening the port and device detection needed? (0 = no delay, >0 = delay in milliseconds)
-device.open.portdelay = 1000
+device.open.portdelay = 2000
+# The receive timeout for the device (in milliseconds, 100 = default, <=0 = no timeout)
+device.receive.timeout = 100
 # Does the device need a high or low DTR-line to operate correctly? (high = true, low = false)
 device.open.portdtr = true
 # Which metadata keys correspond to this device profile? Value is a comma-separated list of (double quoted) names...
 device.metadata.keys = "AGLAMv0"
 
-# In which order are samples sent back from the device? true = last sample first, false = first sample first
-device.samples.reverseOrder = false
+# In which order are samples sent back from the device? false = last sample first, true = first sample first
+device.samples.reverseOrder = true
 
 ###EOF###